Official DistributorSKU
MPN
PSR-SCP- 24DC/SSM/2X1
Weight
0.223 kg
Series PSR-SCP
PSR-SCP- 24DC/SSM/2X1 - Safety relay module
Two-channel over-speed safety relay, 2 N/O contacts for SIL 3 in acc. with IEC 61508, control with two standard initiators, pluggable screw connection terminal blocks, width: 22.5 mm
- Standard sensors can be connected
- Up to SIL 3 in accordance with IEC 61508
- Easy configuration via software (PSR-RSM4)
Technical Specifications
Utilization restriction
| EMC note | EMC: class A product, see manufacturer's declaration in the download area |
Product properties
| Application | Zero-speed safety relay |
| Mechanical service life | > 20x 106 cycles |
| Relay type | Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3 |
Electrical properties
| Nominal operating mode | 100% operating factor |
| Interfaces | Initiator connection |
Air clearances and creepage distances between the power circuits
| Rated Insulation Voltage | 250 V |
| Rated surge voltage/insulation | 4 kV / Basic isolation, (safe isolation, reinforced insulation and 6 kV between input circuit and enabling current paths.) |
General
| Nominal input voltage UN | 24 V DC |
| Input voltage range in reference to UN | 0.85 ... 1.1 |
| Typical input current at UN | 60 mA |
| Voltage at input/start and feedback circuit | approx. 24 V DC |
| Typical response time | 12 ms |
| Typical release time | 8 ms |
| Recovery time | 1 s |
| Protective circuit | Surge protection; Suppressor diode |
| Limit frequency | 2 kHz |
| Switching range (operation) | > 2.5 Hz |
| Switching range (complete stop) | < 2 Hz |
| Status display | Green LED |
Output data
| Contact switching type | 2 enabling current paths |
| Contact switching type | 2 signaling current paths |
| Contact Material | AgNi10, + 5 µm Au |
| Maximum Switching Voltage | 250 V AC/DC (when the gold layer is destroyed) |
| Maximum Switching Voltage | 60 V AC/DC (with gold layer existing) |
| Minimum Switching Voltage | 100 mV AC/DC |
| Limiting Continuous Current | 5 A |
| Limiting Continuous Current | 100 mA (alarm outputs) |
| Maximum Inrush Current | 5 A |
| Inrush current, minimum | 1 mA |
| Sq. Total current | 20.5 A2 (ITH2 = I12 + I22) |
| Interrupting rating (ohmic load) max. | 120 W (24 V DC, τ = 0 ms) |
| Interrupting rating (ohmic load) max. | 130 W (48 V DC, τ = 0 ms) |
| Interrupting rating (ohmic load) max. | 88 W (110 V DC, τ = 0 ms) |
| Interrupting rating (ohmic load) max. | 66 W (220 V DC, τ = 0 ms) |
| Switching capacity min. | 1 mW |
| Switching capacity (3600/h cycles) | 2 A (24 V (DC13)) |
| Switching capacity (3600/h cycles) | 3 A (230 V (AC15)) |
| Output fuse | 6 A gL |
Conductor connection
| Connection Method | Screw connection |
| Conductor cross section, rigid | 0.2 mm² ... 2.5 mm² |
| Conductor cross section, flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section AWG | 24 ... 12 |
| Stripping length | 7 mm |
| Screw thread | M3 |
Dimensions
| Width | 22.5 mm |
| Height | 99 mm |
| Depth | 114.5 mm |
Material specifications
| Color | yellow |
Safety data
| Stop category | 0 |
| Category in acc. with EN 954-1 | 4 |
Safety data: IEC 61508 - High demand
| Safety Integrity Level (SIL) | 3 |
Ambient conditions
| Degree of Protection | IP54 |
| Degree of Protection | IP20 |
| Min. degree of protection of inst. location | IP54 |
| Ambient Temperature (Operation) | -20 °C ... 55 °C |
| Ambient temperature (storage/transport) | -40 °C ... 70 °C |
| Maximum altitude | max. 2000 m (Above sea level) |
| Max. permissible humidity (storage/transport) | 75 % (on average, 85% infrequently, non-condensing) |
| Max. permissible relative humidity (operation) | 75 % (on average, 85% infrequently, non-condensing) |
Air clearances and creepage distances between the power circuits
| Standards/regulations | EN 60664/VDE 0110 |
Mounting
| Mounting Type | DIN rail mounting |
| Assembly instructions | in rows with zero spacing |
| Mounting Position | any |
Why Proax for Phoenix Contact 2981567?
Proax is an authorized distributor of Phoenix Contact 2981567 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
2981936 - Interface module for the connection of several safety sensors or switches with NC/NO contacts to the safety relay PSR-SDC4, with screw connection
1442021 - 1-channel or 2-channel contact extension, 5 N/O contacts, 1 N/C contact, 1 confirmation current path, together with basic device up to Cat. 4 PL e in accordance with EN ISO 13849 safe isolation, width: 35 mm, pluggable screw terminal block
2986960 - Safe coupling relay for SIL 3 high- and low-demand applications, couples digital output signals to the periphery, two enabling current paths, one signal contact, module for safe state off applications, integrated test pulse filter, plug-in screw connection, width: 17.5 mm
2981978 - Safe coupling relay for SIL 3 high- and low-demand applications, couples digital output signals to the periphery, one enabling current path, one signal contact, module for safe state off applications, test pulse filter, fuse, plug-in screw connection, width: 17.5 mm
2986575 - Safe coupling relay for SIL 2 high- and low-demand applications, couples digital output signals to the periphery, two enabling current paths, one signal contact, module for safe state off applications, integrated test pulse filter, plug-in screw connection, width: 17.5 mm
2986711 - Coupling relay for SIL 3 low demand applications, couples digital output signals to the periphery, 1 enabling current path, module for F&G applications, test pulse filter, plug-in screw connection, 17.5 mm width
PSR-SCP- 24DC/ESD/5X1/1X2/ T 1, Safety relay for emergency stop and safety door monitoring up to SIL 3 or Cat. 4, PL e according to EN ISO 13849, automatic or manual activation, 3 N/O contacts, 1 N/C contact, 2 N/O contacts with fixed 1.0 s dropout delay, plug-in screw connection terminal blocks
