Official DistributorSKU
MPN
MINI MCR-SL-SHUNT-UI-NC
Weight
0.118 kg
This product is Not Cancellable/Not Returnable
MINI MCR-SL-SHUNT-UI-NC - Signal conditioner
MCR 3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV range, both unipolar and bipolar with screw connection, not preconfigured
- Power supply possible via the foot element (TBUS)
- Ideal for converting signals for shunt measurements
- Low power consumption
- Highly-compact isolating amplifier for electrical isolation, conversion, amplification, and filtering of mV signals to create standard analog signals
- Up to 280 signal combinations can be configured using DIP switches
- 3-way isolation
Technical Specifications
Utilization restriction
| EMC note | EMC: class A product, see manufacturer's declaration in the download area |
Product properties
| Product family | MINI Analog |
| No. of channels | 1 |
| Configuration | DIP switches |
Insulation characteristics
| Overvoltage category | II |
| Pollution degree | 2 |
Electrical properties
| Electrical isolation | Basic insulation in accordance with EN 61010 |
| Electrical isolation between input and output | yes |
| Limit frequency (3 dB) | 100 Hz / 30 Hz switchable |
| Step response (10-90%) | 3.5 ms (100 Hz) |
| Maximum temperature coefficient | < 0.01 %/K |
| Temperature coefficient, typical | < 0.002 %/K |
| Maximum transmission error | ≤ 0.2 % |
| Maximum transmission error | < 0.4 % (Without adjustment) |
Electrical isolation Input/output/power supply
| Rated Insulation Voltage | 30 V AC |
| Rated Insulation Voltage | 50 V DC |
| Test voltage | 1.5 kV AC (50 Hz, 60 s) |
Supply
| Nominal Supply Voltage | 24 V DC |
| Supply Voltage Range | 19.2 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715) |
| Max. current consumption | < 25 mA |
| Power consumption | < 450 mW (Current output) |
Signal: Voltage
| Number of Inputs | 1 |
| Configurable/programmable | Yes, unconfigured |
| Voltage input signal | -50 mV ... 50 mV |
| Voltage input signal | -60 mV ... 60 mV |
| Voltage input signal | -75 mV ... 75 mV |
| Voltage input signal | -80 mV ... 80 mV |
| Voltage input signal | -100 mV ... 100 mV |
| Voltage input signal | -120 mV ... 120 mV |
| Voltage input signal | -150 mV ... 150 mV |
| Voltage input signal | -200 mV ... 200 mV |
| Voltage input signal | -240 mV ... 240 mV |
| Voltage input signal | -300 mV ... 300 mV |
| Voltage input signal | -500 mV ... 500 mV |
| Voltage input signal | -600 mV ... 600 mV |
| Voltage input signal | -750 mV ... 750 mV |
| Voltage input signal | -800 mV ... 800 mV |
| Voltage input signal | -1 V ... 1 V |
| Voltage input signal | -1.2 V ... 1.2 V |
| Voltage input signal | -1.5 V ... 1.5 V |
| Voltage input signal | -2 V ... 2 V |
| Voltage input signal | -2.4 V ... 2.4 V |
| Voltage input signal | -3 V ... 3 V |
| Voltage input signal | 0 mV ... 50 mV (additional areas can be configured, see table) |
| Voltage input signal | 0 mV ... 60 mV |
| Voltage input signal | 0 mV ... 75 mV |
| Voltage input signal | 0 mV ... 80 mV |
| Voltage input signal | 0 mV ... 100 mV |
| Voltage input signal | 0 mV ... 120 mV |
| Voltage input signal | 0 mV ... 150 mV |
| Voltage input signal | 0 mV ... 200 mV |
| Voltage input signal | 0 mV ... 240 mV |
| Voltage input signal | 0 mV ... 300 mV |
| Voltage input signal | 0 mV ... 500 mV |
| Voltage input signal | 0 mV ... 600 mV |
| Voltage input signal | 0 mV ... 750 mV |
| Voltage input signal | 0 mV ... 800 mV |
| Voltage input signal | 0 V ... 1 V |
| Voltage input signal | 0 V ... 1.2 V |
| Voltage input signal | 0 V ... 1.5 V |
| Voltage input signal | 0 V ... 2 V |
| Voltage input signal | 0 V ... 2.4 V |
| Voltage input signal | 0 V ... 3 V |
| Max. voltage input signal | approx. 3 V DC |
| Input resistance of voltage input | approx. 10 kΩ |
Signal: Voltage/current
| Number of Outputs | 1 |
| Configurable/programmable | Yes, unconfigured |
| Voltage output signal | 0 V ... 10 V |
| Voltage output signal | 2 V ... 10 V |
| Voltage output signal | 0 V ... 5 V |
| Voltage output signal | 1 V ... 5 V |
| Voltage output signal | -10 V ... 10 V (The bi-polar output can be used only for bi-polar input signals.) |
| Voltage output signal | -5 V ... 5 V (The bi-polar output can be used only for bi-polar input signals.) |
| Current Output Signal | 0 mA ... 20 mA |
| Current Output Signal | 4 mA ... 20 mA |
| Load/output load voltage output | ≥ 10 kΩ |
| Load/Output Load Current Output | < 500 Ω (at 20 mA) |
| Ripple | < 20 mVPP (at 500 Ω) |
| Ripple | < 20 mVPP (at 10 kΩ) |
Connection data
| Connection Method | Screw connection |
| Connection technology | 2-conductor |
| Stripping length | 12 mm |
| Screw thread | M3 |
| Conductor cross section rigid | 0.2 mm² ... 2.5 mm² |
| Conductor cross section flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section AWG | 26 ... 12 |
Dimensions
| Width | 6.2 mm |
| Height | 93.1 mm |
| Depth | 102.5 mm |
Material specifications
| Color | green (RAL 6021) |
| Housing Material | PBT |
| Fire protection for rail vehicles (DIN EN 45545-2) R22 | HL 1 - HL 2 |
| Fire protection for rail vehicles (DIN EN 45545-2) R23 | HL 1 - HL 2 |
| Fire protection for rail vehicles (DIN EN 45545-2) R24 | HL 1 - HL 2 |
Ambient conditions
| Degree of Protection | IP20 |
| Ambient Temperature (Operation) | -20 °C ... 65 °C |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Altitude | ≤ 2000 m |
| Permissible humidity (operation) | 5 % ... 95 % (non-condensing) |
CE
| Certificate | CE-compliant |
UKCA
| Certificate | UKCA-compliant |
UL, USA/Canada
| Identification | UL 508 Recognized |
| Identification | Class I, Div. 2, Groups A, B, C, D T4 |
Shipbuilding approval
| Certificate | DNV GL TAA000020N |
DNV GL data
| Temperature | B |
| Humidity | B |
| Vibration | B |
| EMC | A |
| Enclosure | Required protection according to the Rules shall be provided upon installation on board |
EMC data
| Noise immunity | EN 61000-6-2 |
| Note | When being exposed to interference, there may be minimal deviations. |
| Electromagnetic compatibility | Conformance with EMC directive |
| Noise emission | EN 61000-6-4 |
Electrostatic discharge
| Standards/regulations | EN 61000-4-2 |
| Comments | Safety measures must be taken to prevent electrostatic discharge. |
Electromagnetic HF field
| Designation | Electromagnetic RF field |
| Standards/regulations | EN 61000-4-3 |
| Typical deviation from the measuring range final value | 6 % |
Fast transients (burst)
| Designation | Fast transients (burst) |
| Standards/regulations | EN 61000-4-4 |
| Typical deviation from the measuring range final value | 6 % |
Surge current load (surge)
| Standards/regulations | EN 61000-4-5 |
| Comments | Criterion B |
Conducted interference
| Designation | Conducted interferences |
| Standards/regulations | EN 61000-4-6 |
| Typical deviation from the measuring range final value | 6 % |
Standards and Regulations
| Electrical isolation | Basic insulation in accordance with EN 61010 |
Mounting
| Mounting Type | DIN rail mounting |
| Assembly instructions | The DIN rail connector can be used for bridging the supply voltage. It can be snapped onto a 35 mm EN 60715 DIN rail. |
| Mounting Position | any |
Accessories
2811815 - MINI analog multiplexer, generates one analog output from 8 analog input signals, for MINI analog module with screw connection.
2864134 - MCR power terminal block for supplying several MINI Analog modules via the DIN rail connector, with screw connection, maximum current consumption of up to 2 A
2866983 - Please use the following item in new systems: 2904614Primary-switched MINI POWER power supply for DIN rail mounting, input: 1-phase, output: 24 V DC/1.5 A
2869728 - DIN rail connector for DIN rail mounting. Universal for TBUS housing. Gold-plated contacts, 5-pos.
2308111 - Fold up transparent cover for MINI MCR modules with additional labeling option using insert strips and flat Zack marker strip 6.2 mm
Why Proax for Phoenix Contact 2810780?
Proax is an authorized distributor of Phoenix Contact 2810780 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
2810793 - MCR 3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV range, both･unipolar･and･bipolar with spring-cage connection, not preconfigured. Replacement part: 2902021 MINI MCR-2-U-UI-PT.
2864079 - MCR repeater power supply with HART transparency, input signal: 4 mA ... 20 mA, output signal: 4 mA ... 20 mA, with screw connection
2810230 - MCR repeater power supply with HART transmission, input signal: 4 mA...20 mA, output signal: 4 mA...20 mA, with spring-cage connection. Replacement part: 2902015 MINI MCR-2-RPSS-I-I-PT.
2864422 - MCR repeater power supplies, screw connection, input signal: (0)4..20 mA, output signal: (0)4..20 mA
2864752 - MCR repeater power supply, with spring-cage connection, input signal: (0)4...20 mA, output signal: (0)4...20 mA. Replacement part: 2902015 MINI MCR-2-RPSS-I-I-PT.
2811420 - Feed-through terminal block for transmission of signals that are already electrically isolated
2864299 - MCR temperature transducer for thermocouples, can be configured via DIP switches, with screw connection, standard configuration
2864480 - MCR limit value switch, with adjustable hysteresis and delay time, with screw connection
2864493 - MCR threshold value switch, with adjustable hysteresis and delay time, with spring-cage connection. Replacement part: 2902035 MINI MCR-2-UI-REL-PT.
2864163 - MCR 3-way signal conditioner, input/output can be configured via DIP switches, for the electrical isolation of analog signals, with spring-cage connection, standard configuration. Replacement part: 2902040 MINI MCR-2-UI-UI-PT.
2864150 - 3-way isolating amplifier for the electrical isolation of analog signals, I/O can be configured via DIP switches, with screw connection, standard configuration- 2864040 - Non-functioning sample; sample module of a MINI MCR-SL-UI-UI 3-way isolating amplifier.
2864082 - Analog frequency transducers for converting analog standard signals into frequency signals or PWM signals, configurable via DIP switch, with screw connection
2902829 - 2-way loop-powered isolating amplifier (supplied on the output side), can be configured via DIP switches, with screw connection technology and standard configuration.
2902830 - Output-side-powered 2-way loop-powered signal conditioner, can be configured via DIP switches, with spring-cage connection technology, standard configuration. Replacement part: 2902063 MINI MCR-2-UI-I-OLP-PT.
2810243 - MCR analog frequency converter for converting standard analog signals into frequency signals or PWM signals, with spring-cage connection. Replacement part: 2902032 MINI MCR-2-UI-FRO-PT.
2864189 - MCR 4-way signal duplicator for electrical isolation and doubling of analog signals with spring-cage connection, standard configuration. Replacement part: 2905028 MINI MCR-2-UNI-UI-2UI-PT..
2864176 - 4-way signal duplicator for electrical isolation and duplication of analog signals with screw connection, standard configuration- 2864794 - MCR 4-way signal duplicator for the electrical isolation and doubling of analog signals with screw connection, order configuration. Replacement part: 2905025 MINI MCR-2-UI-2UI-C.
- 2864134 - MCR power terminal block for supplying several MINI Analog modules via the DIN rail connector, with screw connection, maximum current consumption of up to 2 A