Official DistributorSKU
MPN
PACT RCP-4000A-1A-D95
Weight
0.431 kg
This product is Not Cancellable/Not Returnable
Series PACT-RCP
PACT RCP-4000A-1A-D95 - Current transformer
Set consisting of a 1 A measuring transducer and a Rogowski coil with signal line. Length of Rogowski coil: 300 mm, diameter: 95 mm. Length of signal line: 3 m. The Rogowski coil measures the AC current of busbars and power lines.
Technical Specifications
Insulation characteristics
| Insulation | double insulation |
| Insulation | double insulation |
| Overvoltage category | III (1000 V, to neutral conductor) |
| Overvoltage category | IV (600 V, to neutral conductor) |
| Pollution degree | 2 |
Electrical properties
| Electrical isolation | Reinforced insulation in accordance with IEC 61010-1 |
| Typical measuring error | < 1 % |
| Protective circuit | Surge protection; 33 V suppressor diode |
| Temperature coefficients | 0.005 %/K (+10 °C ... +70 °C, both components have the same ambient temperature) |
| Temperature coefficients | 0.07 %/K (-20 °C ... +10 °C, both components have the same ambient temperature) |
Measuring coil
| Conductor structure signal line | 2x 0.22 mm (Signal (tinned)) |
| Conductor structure signal line | 1x 0.22 mm (Shielding (tinned)) |
| Insulation | double insulation |
| Rated Insulation Voltage | 1000 V AC (rms CAT III) |
| Rated Insulation Voltage | 600 V AC (rms CAT IV) |
| Test voltage | 10.45 kV DC (60 s) |
| Basic accuracy | <± 0.2 % |
Measuring transducers
| Linearity error | < 0.5 % (From the range end value) |
| Maximum transmission error | ≤ 0.5 % (From the range end value) |
| Frequency Range | 45 Hz ... 65 Hz |
| Max. detectable harmonics | < 2 kHz |
| Current consumption | < 190 mA (at 19.2 V) |
| Test voltage | 1.5 kV AC (Supply/input and output: 50 Hz, 1 min) |
General
| Can be calibrated | no |
| Class | 1 |
| Accuracy class | 1 |
| Converter type | Rogowski coil and 1 A measuring transducer |
Supply: Measuring transducers
| Nominal Supply Voltage | 24 V DC -20 % ... +25 % |
| Nominal supply voltage range | 19.2 V DC ... 30 V DC |
| Max. current consumption | 190 mA |
| Power consumption | 4 W |
Frequency
| Designation | Measuring coil |
| Frequency measuring range | 40 Hz ... 20000 Hz |
| Position error | <± 0.1 % (typical) |
| Linearity error | < 0.1 % |
Signal
| Input signal (at 50 Hz) | 100 mV (1000 A) |
| Curve type | Sine |
| Input Impedance | 27 kΩ (smallest measuring range) |
Current transformers
| Configurable/programmable | Via DIP switches |
| Rated power | 1.5 VA |
| Primary rated current Ipn | 0 A AC ... 100 A AC |
| Primary rated current Ipn | 0 A AC ... 250 A AC |
| Primary rated current Ipn | 0 A AC ... 400 A AC |
| Primary rated current Ipn | 0 A AC ... 630 A AC |
| Primary rated current Ipn | 0 A AC ... 1000 A AC |
| Primary rated current Ipn | 0 A AC ... 1500 A AC |
| Primary rated current Ipn | 0 A AC ... 2000 A AC |
| Primary rated current Ipn | 0 A AC ... 4000 A AC |
| Phase angle | < 1 ° |
| Can be calibrated | no |
| Class | 1 |
| Accuracy class | 1 |
| Converter type | Rogowski coil and 1 A measuring transducer |
Signal
| Designation | Measuring coil |
| Output signal (at 50 Hz) | 100 mV (no load, at 1,000 A) |
| Output voltage (in no-load operation) | VOUT = M * dI/dt |
| Output voltage (sinusoidal, in no-load operation) | 100 mV (VOUT = 2 * π * M * f * I (M = 0.318 μH; example: At 50 Hz; I = 1,000 A)) |
| Accuracy class | < 1 |
| Designation | Measuring transducer |
| Current Output Signal | 0 A AC ... 1 A AC |
| Rated power | 1.25 VA |
| Load | 0 Ω ... 1.25 Ω |
| Max. distances for copper cables at PN max | 16 m (0.75 mm² (AWG 20)) |
| Max. distances for copper cables at PN max | 32 m (1.5 mm² (AWG 16)) |
| Max. distances for copper cables at PN max | 55 m (2.5 mm² (AWG 14)) |
Measuring transducer side
| Connection Method | Screw connection |
| Stripping length | 7 mm |
| Screw thread | M3 |
| Conductor cross section rigid | 0.2 mm² ... 2.5 mm² |
| Conductor cross section flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section AWG | 24 ... 14 |
| Tightening torque | 0.5 Nm ... 0.6 Nm |
Signaling
| Operating voltage display | Green LED |
Item dimensions
| Width | 22.5 mm |
| Height | 85 mm |
| Depth | 70.4 mm |
Measuring coil
| Length | 300 mm |
| Diameter | 8.3 mm ±0.2 mm |
Measuring coil when installed
| Diameter | 95 mm |
Signal line
| Length | 3 m |
| Width | 22.5 mm |
| Height | 85 mm |
| Depth | 70.4 mm |
Material specifications
| Housing Material | PC |
| Housing Material | Polyamide |
| Coil material | Elastollan |
Ambient conditions
| Measuring coil degree of protection | IP67 (not assessed by UL) |
| Measuring transducer degree of protection | IP20 |
| Ambient Temperature (Operation) | -30 °C ... 80 °C (Measuring coil) |
| Ambient Temperature (Operation) | -20 °C ... 70 °C (Measuring transducer) |
| Ambient temperature (storage/transport) | -40 °C ... 80 °C (Measuring coil) |
| Ambient temperature (storage/transport) | -25 °C ... 85 °C (Measuring transducer) |
| Altitude | < 2000 m |
| Permissible humidity (operation) | 5 % ... 95 % (non-condensing) |
CE
| Certificate | CE-compliant |
UKCA
| Certificate | UKCA-compliant |
CMIM
| Certificate | CMIM-compliant |
UL, USA/Canada
| Identification | UL 61010 Recognized |
| Note | Measuring coil |
| Identification | UL 508 Listed |
| Note | Measuring transducer |
EMC data
| Noise immunity | EN 61000-6-3 |
| Electromagnetic compatibility | Conformance with EMC directive |
| Noise emission | EN 61000-6-4 |
Standards and Regulations
| Electrical isolation | Reinforced insulation in accordance with IEC 61010-1 |
| Standards/regulations | IEC 61010-1 |
| Standards/regulations | IEC 61010-2-032 |
Mounting
| Mounting Type | DIN rail mounting |
Accessories
2904895 - The optional holding device ensures the Rogowski coil is securely seated on busbars with a thickness of 10 ... 15 mm. During installation, the coil housing is pushed onto the flange of the holding device and snaps in automatically.- 2907888 - The optional holding device ensures the Rogowski coil is securely seated on busbars that are 5 ... 10 mm thick. During installation, the coil housing is pushed onto the flange of the holding device and snaps in automatically.
Why Proax for Phoenix Contact 2904921?
Proax is an authorized distributor of Phoenix Contact 2904921 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
2910326 - Set consisting of a 1 A measuring transducer and a Rogowski coil with signal line. Length of Rogowski coil: 300 mm, diameter: 95 mm. Length of signal line: 10 m. The Rogowski coil measures the AC current of busbars and power lines.- 2910325 - Set consisting of a 1 A measuring transducer and a Rogowski coil with signal line. Length of Rogowski coil: 300 mm, diameter: 95 mm. Length of signal line: 5 m. The Rogowski coil measures the AC current of busbars and power lines.
- 2904922 - Set consisting of one 1 A measuring transducer and one Rogowski coil with signal line. Length of Rogowski coil: 450 mm, diameter: 140 mm. Length of signal line: 3 m. The Rogowski coil measures the AC current of busbars and power lines.
- 1033483 - Set consisting of one 1 A measuring transducer and one Rogowski coil with signal line. Length of Rogowski coil: 450 mm, diameter: 140 mm. Length of signal line: 10 m. The Rogowski coil measures the AC current of busbars and power lines.
1058044 - Set consisting of one 1 A measuring transducer and one UV-resistant Rogowski coil with signal line. Length of Rogowski coil: 450 mm, diameter: 140 mm. Length of signal line: 3 m. The Rogowski coil measures the AC current of busbars and power lines.- 2904923 - Set consisting of a 1 A measuring transducer and a Rogowski coil with signal line. Length of Rogowski coil: 600 mm, diameter: 190 mm. Length of signal line: 3 m. The Rogowski coil measures the AC current of busbars and power lines.
- 2910327 - Set consisting of a 1 A measuring transducer and a Rogowski coil with signal line. Length of Rogowski coil: 600 mm, diameter: 190 mm. Length of signal line: 10 m. The Rogowski coil measures the AC current of busbars and power lines.
- 1033485 - Set consisting of one 1 A measuring transducer and one UV-resistant Rogowski coil with signal line. Length of Rogowski coil: 600 mm, diameter: 190 mm. Length of signal line: 3 m. The Rogowski coil measures the AC current of busbars and power lines.
2902990 - This is an individual product; please order the complete set. The measuring transducer processes the mV signal of the upstream Rogowski coil. The measuring transducer has 8 current measuring ranges (100 A ... 4000 A AC) which can be set; max. output current of 1 A AC.
2906229 - Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.
2906232 - Set consisting of a 4-way signal conditioner with screw connection technology and a Rogowski coil 450 mm in length/140 mm in diameter for AC current measurement on busbars and power lines.The signal conditioner outputs 8 different standard signals on the output side and has one switching output.- 2906233 - Set consisting of a 4-way signal conditioner with screw connection technology and a Rogowski coil 600 mm in length/190 mm in diameter for AC current measurement on busbars and power lines.The signal conditioner outputs 8 different standard signals on the output side and has one switching output.
- 2906231 - Set consisting of a 4-way signal conditioner with screw connection technology and a Rogowski coil 300 mm in length/95 mm in diameter for AC current measurement on busbars and power lines.The signal conditioner outputs 8 different standard signals on the output side and has one switching output.
2906230 - Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Push-in connection technology, order configuration.- 2906235 - Set consisting of a 4-way signal conditioner with push-in connection technology and a Rogowski coil 450 mm in length/140 mm in diameter for AC current measurement on busbars and power lines.The signal conditioner outputs 8 different standard signals on the output side and has one switching output.
- 2906236 - Set consisting of a 4-way signal conditioner with push-in connection technology and a Rogowski coil 600 mm in length/190 mm in diameter for AC current measurement on busbars and power lines.The signal conditioner outputs 8 different standard signals on the output side and has one switching output.
- 2906234 - Set consisting of a 4-way signal conditioner with push-in connection technology and a Rogowski coil 300 mm in length/95 mm in diameter for AC current measurement on busbars and power lines.The signal conditioner outputs 8 different standard signals on the output side and has one switching output.
2904891 - 450 mm long Rogowski coil. The measuring coil diameter when installed is 140 mm. The Rogowski coil is used for AC current measurement for busbars and power lines.- 2904892 - 600 mm long Rogowski coil. The measuring coil diameter when installed is 190 mm. The Rogowski coil is used for AC current measurement for busbars and power lines.