The figure shows a version with a screw connection
Official DistributorSKU
MPN
PSR-MC62-2NO-1DO-24DC-SP
Weight
0.158 kg
Series PSR-MC
PSR-MC62-2NO-1DO-24DC-SP - Safety relays
Safety relay for two-hand controls in accordance with ISO 13851 type IIIC, up to SIL 3, Cat. 4, PL e, synchronous activation monitoring < 0.5 s, 2 enabling current paths, US = 24 V DC, plug-in Push-in terminal block
- Up to Cat. 4/PL e in accordance with EN ISO 13849-1, SIL 3 in accordance with EN IEC 62061
- Type IIIC in accordance with ISO 13851
- Low housing width of just 12.5 mm
- 2 enabling current paths, 1 digital signal output
- Automatic activation
Technical Specifications
Product properties
| Product family | PSRmini |
| Application | Two-hand control |
| Relay type | Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3 |
Times
| Typical response time | < 50 ms |
| Typical release time | < 10 ms (when controlled via S12/S22) |
| Typical release time | < 5 ms (when interrupted via A1; applicative deactivation via A1/A2 is not permitted) |
| Restart time | < 2 s (Boot time) |
| Recovery time | < 500 ms |
Electrical properties
| Maximum power dissipation for nominal condition | 5.09 W (at US = 30 V, IL² = 72 A²) |
| Nominal operating mode | 100% operating factor |
Air clearances and creepage distances between the power circuits
| Rated Insulation Voltage | 250 V AC |
| Rated Insulation Voltage | 250 V AC |
| Rated surge voltage/insulation | Basic insulation 4 kV between all current paths and housing |
| Rated surge voltage/insulation | Safe isolation, reinforced insulation 6 kV:between (A1, A2, S11, S12, S21, S22, S35, M1) and enabling current path (13/14)between (A1, A2, S11, S12, S21, S22, S35, M1) and enabling current path (23/24)between enabling current paths |
Supply
| Designation | A1/A2 |
| Rated control circuit supply voltage US | 19.2 V DC ... 30 V DC |
| Rated control circuit supply voltage US | 24 V DC -20 % / +25 % |
| Rated control supply current IS | typ. 40 mA |
| Power consumption at US | typ. 0.96 W |
| Inrush Current | typ. 20 A (Δt = 10 µs at Us) |
| Filter time | 10 ms (For the logic. At A1 in the event of voltage dips at Us ) |
| Protective circuit | Surge protection; Suppressor diode |
| Protective circuit | Protection against polarity reversal for rated control circuit supply voltage |
Digital: Sensor circuit (S12, S22)
| Description of the input | safety-related sensor inputs |
| Number of Inputs | 2 |
| Inrush Current | < 10 mA (with Us/Ix to S12/S22) |
| Concurrence | < 0.5 s |
| Max. permissible overall conductor resistance | 150 Ω |
| Current consumption | < 4.2 mA (with Us/Ix to S12/S22) |
Digital: Feedback circuit (S35)
| Description of the input | non-safety-related |
| Number of Inputs | 1 |
| Inrush Current | < 5.5 mA (typically with US) |
| Max. permissible overall conductor resistance | 150 Ω |
| Voltage at input/start and feedback circuit | 24 V DC -20 % / +25 % |
| Current consumption | < 5.1 mA (typically with US) |
Relay: Enabling current paths (13/14, 23/24)
| Output description | safety-related N/O contacts |
| Number of Outputs | 2 (undelayed) |
| Contact switching type | 2 enabling current paths |
| Contact Material | AgSnO2 (enabling current path) |
| Switching voltage | min. 12 V AC/DC |
| Switching voltage | max. 250 V AC/DC (Observe the load curve) |
| Switching capacity | min. 60 mW |
| Inrush Current | min. 3 mA |
| Inrush Current | max. 6 A |
| Limiting Continuous Current | 6 A (observe derating) |
| Sq. Total current | 72 A2 (observe derating) |
| Switching frequency | 1 Hz |
| Mechanical service life | 10x 106 cycles |
| Output fuse | 6 A gL/gG (N/O contact) |
Signal: M1
| Output description | PNP |
| Output description | non-safety-related |
| Number of Outputs | 1 (digital, PNP) |
| Voltage | 22 V DC (Us - 2 V) |
| Current | max. 100 mA |
| Maximum Inrush Current | 500 mA (Δt = 1 ms at Us) |
| Short-circuit protection | Yes |
Connection technology
| pluggable | yes |
Conductor connection
| Connection Method | Push-in connection |
| Conductor cross section rigid | 0.2 mm² ... 1.5 mm² |
| Conductor cross section flexible | 0.2 mm² ... 1.5 mm² |
| Conductor cross section, flexible, with ferrule, with plastic sleeve | 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6) |
| Conductor cross section flexible, with ferrule without plastic sleeve | 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6) |
| Conductor cross-section AWG | 24 ... 16 |
| Stripping length | 8 mm |
Signaling
| Status display | 5 x bi-color LED |
Dimensions
| Width | 12.5 mm |
| Height | 116.6 mm |
| Depth | 114.5 mm |
Material specifications
| Color | yellow |
| Housing Material | Polyamide |
Safety data
| Stop category | 0 |
| Type class | IIIC |
Safety data: EN ISO 13849
| Category | 4 (4 A DC13; 5 A AC15; 8760 switching cycles/year) |
| Performance level (PL) | e (4 A DC13; 5 A AC15; 8760 switching cycles/year) |
Safety data: IEC 61508 - High demand
| Safety Integrity Level (SIL) | 3 (4 A DC13; 5 A AC15; 8760 switching cycles/year) |
Safety data: EN IEC 62061
| Safety Integrity Level (SIL) | 3 (4 A DC13; 5 A AC15; 8760 switching cycles/year) |
Ambient conditions
| Degree of Protection | IP20 |
| Min. degree of protection of inst. location | IP54 |
| Ambient Temperature (Operation) | -35 °C ... 60 °C (observe derating) |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Maximum altitude | ≤ 2000 m (Above sea level) |
| Max. permissible humidity (storage/transport) | 75 % (on average, 85% infrequently, non-condensing) |
| Max. permissible relative humidity (operation) | 75 % (on average, 85% infrequently, non-condensing) |
| Shock | 15g |
| Vibration (Operation) | 10 Hz ... 150 Hz, 2g |
CE
| Identification | CE-compliant |
Air clearances and creepage distances between the power circuits
| Standards/regulations | DIN EN 50178 |
Mounting
| Mounting Type | DIN rail mounting |
| Assembly instructions | See derating curve |
| Mounting Position | vertical or horizontal |
Why Proax for Phoenix Contact 2700575?
Proax is an authorized distributor of Phoenix Contact 2700575 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
Extension de contacts jusqu'à la limite de sollicitation SIL 3, cat. 4, PL e en association avec l'analyseur approprié, 5 circuits de validation, US = 24 V DC, bloc de jonction Push-in enfichable
