2320021
Official DistributorSKU
PHX2320021
MPN
MINI-PS- 12- 24DC/48DC/0.7
Weight
0.232 kg
This product is Not Cancellable/Not Returnable
Series MINI-PS
MINI-PS- 12- 24DC/48DC/0.7 - DC/DC converter
Please use the following item in new systems: 1098676.Primary-switched MINI DC/DC converter for DIN rail mounting, input: 12 - 24 V DC, output: 48 V DC/0.7 A
- Electrical isolation: for setting up independent supply systems
- Support conversion to various voltage levels
- Constant voltage: output voltage regenerated even at the end of long cables
Technical Specifications
DC operation
| Nominal input voltage range | 12 V DC ... 24 V DC |
| Input voltage range | 10 V DC ... 32 V DC (> 10.5 V DC start) |
| Wide-range input | yes |
| Input voltage range DC | 10 V DC ... 32 V DC (> 10.5 V DC start) |
| Voltage type of supply voltage | DC |
| Inrush Current | < 10 A (typical) |
| Inrush current integral (I2t) | 0.3 A2s |
| Frequency range DC | 0 Hz |
| Mains buffering time | typ. 2 ms (12 V DC) |
| Mains buffering time | typ. 12 ms (24 V DC) |
| Current consumption | 3.2 A (12 V DC) |
| Current consumption | 1.6 A (24 V DC) |
| Typical response time | < 0.5 s |
| Input fuse | 6.3 A (slow-blow, internal) |
Output data
| Efficiency | > 87 % (at 24 V DC and nominal values) |
| Output characteristic | U/I |
| Nominal Output Voltage | 48 V DC ±1 % |
| Setting range of the output voltage (USet) | 30 V DC ... 56 V DC (> 48 V DC, constant capacity restricted) |
| Nominal output current (IN) | 0.7 A (-25 °C ... 60 °C) |
| Derating | 60 °C ... 70 °C (2.5 %/K) |
| Feedback voltage resistance | 60 V DC |
| Protection against overvoltage at the output (OVP) | < 60 V DC |
| Residual ripple | < 20 mVPP (20 MHz) |
| Output Power | 33.6 W |
| Peak switching voltages nominal load | < 10 mVPP (20 MHz) |
| Maximum no-load power dissipation | < 1.5 W |
| Power loss nominal load max. | < 4.5 W |
| Connection in parallel | yes, for assembling redundant systems and increasing efficiency |
| Connection in series | yes |
Signal: DC OK active
| Output description | UOUT > 0.9 x UN: High signal |
| Output Voltage | + 24 V (Signal) |
| Continuous load current | ≤ 20 mA |
Input
| Connection Method | Pluggable screw connection |
| Conductor cross section, rigid min. | 0.2 mm² |
| Conductor cross section, rigid max. | 2.5 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 14 |
| Stripping length | 7 mm |
| Screw thread | M3 |
| Tightening torque, min | 0.5 Nm |
| Tightening torque max | 0.6 Nm |
Output
| Connection Method | Pluggable screw connection |
| Conductor cross section, rigid min. | 0.2 mm² |
| Conductor cross section, rigid max. | 2.5 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 14 |
| Stripping length | 7 mm |
| Screw thread | M3 |
| Tightening torque, min | 0.5 Nm |
| Tightening torque max | 0.6 Nm |
Signal
| Conductor cross section, rigid min. | 0.2 mm² |
| Conductor cross section, rigid max. | 2.5 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 14 |
| Screw thread | M3 |
| Tightening torque, min | 0.5 Nm |
| Tightening torque max | 0.6 Nm |
Signaling
| Types of signaling | LED |
| Types of signaling | Active switching output |
Signal output: DC OK active
| Status display | "DC OK" LED green |
| Note on status display | UOUT > 0.9 x UN: LED ON |
| Color | green |
| Note on status display | LED on |
Electrical properties
| Number of phases | 1.00 |
| Insulation voltage input/output | 1.5 kV (type test) |
| Insulation voltage input/output | 1 kV (routine test) |
Product properties
| MTBF (IEC 61709, SN 29500) | > 1993000 h (40 °C) |
Insulation characteristics
| Protection class | III |
| Degree of pollution | 2 |
Dimensions
| Width | 22.5 mm |
| Height | 99 mm |
| Depth | 107 mm |
Installation dimensions
| Installation distance right/left | 0 mm / 0 mm (≤ 70 °C) |
| Installation distance top/bottom | 50 mm / 50 mm (≤ 70 °C) |
Mounting
| Assembly instructions | alignable: horizontally 0 mm, vertically 50 mm |
| Mounting Position | horizontal DIN rail NS 35, EN 60715 |
| With protective coating | No |
Material specifications
| Housing Material | Plastic |
| Housing Material | Polyamide (PA) |
| Type of housing | Polyamide PA, color: green |
Ambient conditions
| Degree of Protection | IP20 |
| Ambient Temperature (Operation) | -25 °C ... 70 °C (> +60°C derating) |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Climatic class | 3K3 (in acc. with EN 60721) |
| Max. permissible relative humidity (operation) | ≤ 95 % (At +25°C, non-condensing) |
| Shock | 18 ms, 30g, in each space direction (according to IEC 60068-2-27) |
| Vibration (Operation) | < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) |
| Vibration (Operation) | 15 Hz ... 150 Hz, 2.3g |
Standards and Regulations
| Rail applications | EN 50121-4 |
| Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations | EN 50178/VDE 0160 (PELV) |
| Standard - Electrical safety | EN 60950-1/VDE 0805 (SELV) |
| Standard - Safe isolation | DIN VDE 0100-410 |
| Standard - Safe isolation | DIN VDE 0106-101 |
Approvals
| CSA | CSA-C22.2 No. 107.1-01 |
| UL approvals | UL/C-UL listed UL 508 |
| UL approvals | UL/C-UL Recognized UL 60950-1 |
| UL approvals | UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D (Hazardous Location) |
EMC data
| Low Voltage Directive | Conformance with Low Voltage Directive 2014/35/EC |
| EMC requirements for noise emission | EN 61000-6-3 |
| EMC requirements for noise emission | EN 61000-6-4 |
| EMC requirements for noise immunity | EN 61000-6-1 |
| EMC requirements for noise immunity | EN 61000-6-2 |
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
| Noise emission | EN 55011 (EN 55022) |
Electrostatic discharge
| Standards/regulations | EN 61000-4-2 |
| Housing | > Level 3 |
| Contact discharge | 8 kV (Contact discharge) |
| Discharge in air | 8 kV (Air discharge) |
| Comments | Criterion B |
Electromagnetic HF field
| Standards/regulations | EN 61000-4-3 |
| Frequency Range | 80 MHz ... 3 GHz |
| Test field strength | 10 V/m |
| Comments | Criterion A |
Fast transients (burst)
| Standards/regulations | EN 61000-4-4 |
| Input | 4 kV (level 4 - asymmetrical: conductor to ground) |
| Output | 2 kV (level 3 - asymmetrical: conductor to ground) |
| Signal | 1 kV (Level 2 - asymmetrical cable to ground) |
| Comments | Criterion B |
Surge voltage load (surge)
| Standards/regulations | EN 61000-4-5 |
| Input | 2 kV (Level 3) |
| Input | 1 kV (Level 3) |
Conducted interference
| Standards/regulations | EN 61000-4-6 |
| Input/Output | Level 3 |
| Frequency Range | 0.15 MHz ... 80 MHz (10 V) |
Voltage dips
| Standards/regulations | EN 61000-4-11 |
Emitted interference
| Standards/regulations | EN 61000-6-3 |
| Radio interference voltage in acc. with EN 55011 | EN 55011 (EN 55022) Class B, area of application: Industry and residential |
| Emitted radio interference in acc. with EN 55011 | EN 55011 (EN 55022) Class B, area of application: Industry and residential |
Why Proax for Phoenix Contact 2320021?
Proax is an authorized distributor of Phoenix Contact 2320021 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
MINI-PS- 12- 24DC/24DC/1 - Please use the following items in new systems: 1066703, 1066716, 1066718, 1066714.Primary-switched MINI DC/DC converter for DIN rail mounting, input: 12 - 24 V DC, output: 24 V DC/1 A
Please use the following item in new systems: 1066704.Primary-switched MINI DC/DC converter for DIN rail mounting, input: 12 V DC ... 24 V DC, output: 5 V DC ... 15 V DC/2 A
MINI-PS- 10- 42AC/15-60DC/3 - The AC feed module supplies the MINI DC/DC converter with a rectified and filtered supply voltage.
Please use the following item in new systems: 1066708.Primary-switched MINI DC/DC converter for DIN rail mounting, input: 48 - 60 V DC, output: 24 V DC/1 A
MINI-PS-100-240AC/24DC/1 - Please use the following items in new systems: 2904597 or 2909575DIN rail power supply, 24 V DC/1 A, primary-switched, narrow design
MINI-PS-100-240AC/24DC/1.3 - Please use the following items in new systems: 2904597 or 2909575Primary-switched MINI POWER power supply for DIN rail mounting, input: 1-phase, output: 24 V DC/1.3 A
MINI-PS-100-240AC/24DC/1.5/EX - Please use the following item in new systems: 2904614Primary-switched MINI POWER power supply for DIN rail mounting, input: 1-phase, output: 24 V DC/1.5 A, for potentially explosive areas
MINI-PS-100-240AC/24DC/2 - Please use the following items in new systems: 2904598 or 2909576Primary-switched MINI POWER power supply for DIN rail mounting, input: 1-phase, output: 24 V DC/2 A
MINI-PS-100-240AC/24DC/4, MINI POWER power supplies for MCR technologyIn measurement and control technology (MCR), modular electronics housing has become the industry standard. MINI POWER is the power supply unit to go with it. The devices are flexible, thanks to special voltages and special versions.
MINI-PS-100-240AC/24DC/C2LPS - Please use the following items in new systems: 2904599 or 2909577Primary-switched MINI POWER power supply for DIN rail mounting, input: 1-phase, output: 24 V DC/100 W
MINI-PS-100-240AC/10-15DC/2 - Please use the following item in new systems: 2904605Primary-switched MINI POWER power supply for DIN rail mounting, input: 1-phase, output: 10 V DC ... 15 V DC/2 A
MINI-PS-100-240AC/10-15DC/8, MINI POWER power supplies for MCR technologyIn measurement and control technology (MCR), modular electronics housing has become the industry standard. MINI POWER is the power supply unit to go with it. The devices are flexible, thanks to special voltages and special versions.
MINI-PS-100-240AC/2X15DC/1, MINI POWER power supplies for MCR technologyIn measurement and control technology (MCR), modular electronics housing has become the industry standard. MINI POWER is the power supply unit to go with it. The devices are flexible, thanks to special voltages and special versions.
MINI-PS-100-240AC/ 5DC/3, MINI POWER power supplies for MCR technologyIn measurement and control technology (MCR), modular electronics housing has become the industry standard. MINI POWER is the power supply unit to go with it. The devices are flexible, thanks to special voltages and special versions.
