Fieldbus communication
MACX MCR-S-MUX-TB - The HART termination board is used to apply the signals from the HART-compatible signal converters or field devices and transmit them to the MACX MCR-S-MUX HART multiplexer.
Not in stock
MACX MCR-S-MUX - HART Multiplexer for online configuration and diagnostics of HART-compatible field devices, as well as for continuous documentation of process variables and states with a PC or management system for mounting on NS 35/7.5 or NS 32
Not in stock
FB-8SP ISO - Zone 1 installed device coupler for Foundation Fieldbus and PROFIBUS PA with terminal connections for eight spurs connected to fieldbus end devices.
Not in stock
FB-ET/E - Trunk module for Foundation Fieldbus and PROFIBUS PA modular device couplers with terminator
Not in stock
FB-PS-MB-25DSUB/EX - Four-channel, redundant fieldbus power supply base. Host connection is a D-SUB 25 socket connector.
Not in stock
FB-PS-MB-Y/EX - Four-channel redundant fieldbus power supply base. Host connections are for two Yokogawa AKB336 20-pin cables.
Not in stock
FB-PS-MB-I/EX - Four-channel, redundant fieldbus power supply base. Host connection is for an Invensys® D-SUB 25 cable.
Not in stock
FB1-S1-6SP-T-0-10-00-0-0 - Stainless steel field junction box with ten ports for use in hazardous locations. Includes six-spur block device coupler (FB-6SP) for Foundation Fieldbus or PROFIBUS PA, three terminal blocks for trunk cable connection (+, –, S).
Not in stock
Four-channel digital input and four-channel digital output module with screw connection. For use with Modbus and OPC UA protocols.
Not in stock
FB2-S1-12SP-T-0-16-00-0-0 - Stainless steel field junction box with 16 ports for use in hazardous locations. Includes 12-spur block device coupler (FB-12SP) for Foundation Fieldbus or PROFIBUS PA, three terminal blocks for trunk cable connection (+, –, S).
Not in stock
FB2-S1-12SP-S-0-16-00-0-0 - Stainless steel field junction box with 16 ports for use in hazardous locations. Includes 12-spur block device coupler (FB-12SP) for Foundation Fieldbus or PROFIBUS PA, trunk cable (+, -, S) is connected to a Plugtrab surge base (PT 4+F-BE).
Not in stock
FB-MODULAR-PP - The FB-MODULAR-PP is a partition plate used between two fieldbus modular device couplers and provides the required 50 mm spacing between an intrinsically safe electrical connection and a non-intrinsically safe electrical connection. The device couplers are 17.5 mm wide, but when adding a partition plate a 22.5 mm TBUS connector is required.
Not in stock
FB-DIAG/FF/LI - Field diagnostics module, legacy installation, includes pluggable side connector
Not in stock
SACCBP-M12MSB-5CON-M16/0,5-900 - Device connector rear mounting, INTERBUS (16 Mbps), 5-position, PUR halogen-free, green RAL 6017, shielded, Pin, straight, M12-SPEEDCON, coding: B, on free cable end, Rear mounting, M16 x 1.5, Cable connection, cable length: 0.5 m, INTERBUS, Alternative product in accordance with RoHS II without Exemption 6c (Pb < 0.1 %) item no.: 1239939
Not in stock
SACC-DSIV-MSB-5CON-L180 SCO THR - Device connector rear mounting, 5-position, Pin, straight, M12-SPEEDCON, coding: B, Rear mounting, M12 x 1, THR solder connection, Alternative product in accordance with RoHS II without Exemption 6c (Pb < 0.1 %) item no.: 1240005
Not in stock