Proax

Currency
0 Items
proax logo
Cart
Phoenix ContactOfficial Distributor

By Phoenix Contact

SKU
MPN
RIF-1-RSC-LDP-24DC/1IC
Weight
0.069 kg
Series RIF

RIF-1-RSC-LDP-24DC/1IC - Relay Module

Preassembled relay module with screw connection, consisting of: relay base, power contact relay, plug-in display/interference suppression module, retaining bracket. Contact switching type: 1 N/O contact, max. inrush current up to 130 A peak, 80 A (20 ms), 24 V DC input voltage

Technical Specifications

Notes

Notes on operationFBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21)

Product properties

Product familyRIFLINE complete
Applicationhigh inrush currents
Operating mode100% operating factor
Mechanical service life3x 107 cycles

Insulation characteristics

InsulationSafe isolation, reinforced insulation

Insulation characteristics: Standards/regulations

InsulationSafe isolation, reinforced insulation
Overvoltage categoryIII
Pollution degree2

Electrical properties

Maximum power dissipation for nominal condition0.43 W
Test voltage (Winding/contact)4 kV AC (50 Hz, 1 min., winding/contact)

Standards/regulations

Rated Insulation Voltage250 V AC
Rated surge voltage6 kV

Coil side

Nominal input voltage UN24 V DC
Input voltage range19.2 V DC ... 33.6 V DC (20 °C)
Input voltage range in reference to UNsee diagram
Drive and functionmonostable
Drive (polarity)polarized
Typical input current at UN18 mA
Typical response time8 ms
Typical release time10 ms
Coil Voltage24 V DC
Protective circuitFreewheeling diode; Freewheeling diode
Operating voltage displayYellow LED

Switching

Contact switching type1 N/O contact
Type of switch contactSingle contact
Contact MaterialAgSnO
Maximum Switching Voltage250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Minimum Switching Voltage12 V (100 mA)
Limiting Continuous Current6 A
Limiting Continuous Current10 A (Value is permissible if connections 11 and 21, as well as connections 14 and 24 are bridged.)
Maximum Inrush Current80 A (20 ms)
Maximum Inrush Current130 A (peak, at capacitive load, 230 V AC, 24 μF)
Min. switching current100 mA (12 V DC)
Interrupting rating (ohmic load) max.264 W (at 24 V DC, observe contact derating)
Interrupting rating (ohmic load) max.58 W (at 48 V DC)
Interrupting rating (ohmic load) max.48 W (at 60 V DC)
Interrupting rating (ohmic load) max.50 W (at 110 V DC)
Interrupting rating (ohmic load) max.80 W (at 220 V DC)
Interrupting rating (ohmic load) max.2750 VA (at 250 V AC, observe contact derating)
Switching capacity min.1200 mW
Utilization category CB Scheme (IEC 60947-5-1)AC15, 6 A/250 V (N/O contact)
Utilization category CB Scheme (IEC 60947-5-1)DC13, 2 A/24 V (N/O contact)

Connection data

Connection MethodScrew connection
Stripping length8 mm
Conductor cross section rigid0.5 mm² ... 4 mm²
Conductor cross-section rigid (2 conductors with same cross section)0.5 mm² ... 2.5 mm²
Conductor cross section flexible0.5 mm² ... 4 mm²
Conductor cross section flexible0.5 mm² ... 4 mm² (Ferrule with plastic sleeve)
Conductor cross section flexible (2 conductors with same cross section)0.5 mm² ... 2.5 mm²
Conductor cross section flexible (2 conductors with same cross section)0.5 mm² ... 1.5 mm² (TWIN ferrule with plastic sleeve)
Conductor cross section AWG20 ... 10 (solid)
Conductor cross section AWG20 ... 12 (flexible)
Tightening torque0.5 Nm ... 0.6 Nm

Dimensions

Width16 mm
Height90 mm
Depth75 mm

Material specifications

Colorgray (RAL 7042)

Ambient conditions

Degree of protection (Relay base)IP20 (Relay base)
Degree of protection (Relay)RT II (Relay)
Degree of protection (Installation location)≥ IP54 (Installation location)
Ambient Temperature (Operation)-40 °C ... 70 °C
Ambient temperature (storage/transport)-40 °C ... 85 °C
Altitude≤ 2000 m

Corrosive gas test

IdentificationISA-S71.04. G3 Harsh Group
IdentificationEN 60068-2-60

Standards/regulations

Standards/regulationsIEC 60947-5-1

Mounting

Mounting TypeDIN rail mounting
Assembly instructionsin rows with zero spacing
Mounting Positionany
Accessories

Why Proax for Phoenix Contact 2909885?

Proax is an authorized distributor of Phoenix Contact 2909885 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.

Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!

Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information

Pack Size10
Recommended
Sold in quantities of 10

Available for order

Phoenix Contact Availability