Official Distributor
SKU
MPN
RIF-2-RPT-LDP-24DC/4X21 AU
Weight
0.105 kg
This product is Not Cancellable/Not Returnable
Series RIF
RIF-2-RPT-LDP-24DC/4X21 AU - Relay Module
Preassembled relay module with Push-in connection, consisting of: relay base, power contact relay with additional hard gold plating, and retaining bracket. Contact switching type: 4 changeover contacts. Input voltage: 24 V DC
Technical Specifications
Product properties
Product family | RIFLINE complete |
Application | Universal |
Operating mode | 100% operating factor |
Mechanical service life | approx. 2x 107 cycles |
Insulation characteristics
Insulation | Basic insulation |
Insulation | Basic insulation |
Overvoltage category | II |
Pollution degree | 2 |
Electrical properties
Maximum power dissipation for nominal condition | 1.01 W |
Test voltage (Winding/contact) | 2.5 kVrms (50 Hz, 1 min., winding/contact) |
Test voltage (Contact/contact) | 2 kVrms (50 Hz, 1 min., contact/contact) |
Rated Insulation Voltage | 250 V AC |
Rated surge voltage | 2.5 kV |
Coil side
Nominal input voltage UN | 24 V DC |
Input voltage range | 19.2 V DC ... 30 V DC (20 °C) |
Input voltage range in reference to UN | see diagram |
Drive and function | monostable |
Drive (polarity) | polarized |
Typical input current at UN | 42 mA |
Typical response time | 13 ms |
Typical release time | 14 ms |
Protective circuit | Freewheeling diode |
Status display | Yellow LED |
Switching
Contact switching type | 4 changeover contacts |
Type of switch contact | Single contact |
Contact Material | AgNi, hard gold-plated |
Note | If the specified maximum values for multi-layer contact relays are exceeded, the gold plating is destroyed. The maximum values of the power contact relay are then valid. This can result in a shorter service life than with a pure power contact. |
Maximum Switching Voltage | 30 V AC |
Maximum Switching Voltage | 36 V DC |
Minimum Switching Voltage | 2 V (24 mA) |
Limiting Continuous Current | 50 mA |
Maximum Inrush Current | 50 mA |
Min. switching current | 2 mA (24 V) |
Interrupting rating (ohmic load) max. | 1.2 W (at 24 V DC) |
Switching capacity min. | 48 mW |
Switching: when the gold layer is destroyed
Note | the following values are applicable if a gold layer is destroyed |
Contact Material | AgNi |
Maximum Switching Voltage | 250 V AC/DC |
Minimum Switching Voltage | 5 V (At 24 mA) |
Limiting Continuous Current | 6 A |
Maximum Inrush Current | 16 A (20 ms, N/O contacts) |
Min. switching current | 5 mA (at 24 V) |
Interrupting rating (ohmic load) max. | 144 W (at 24 V DC) |
Interrupting rating (ohmic load) max. | 124 W (at 48 V DC) |
Interrupting rating (ohmic load) max. | 108 W (at 60 V DC) |
Interrupting rating (ohmic load) max. | 52 W (at 110 V DC) |
Interrupting rating (ohmic load) max. | 48 W (at 220 V DC) |
Interrupting rating (ohmic load) max. | 1500 VA (for 250 V AC) |
Switching capacity | 2 A (at 24 V, DC13) |
Switching capacity | 0.22 A (at 120 V, DC13) |
Switching capacity | 0.11 A (at 250 V, DC13) |
Switching capacity | 1.5 A (at 24 V, AC15) |
Switching capacity | 1.5 A (at 120 V, AC15) |
Switching capacity | 1 A (at 240 V, AC15) |
Connection data
Connection Method | Push-in connection |
Stripping length | 8 mm |
Conductor cross section rigid | 0.14 mm² ... 1.5 mm² |
Conductor cross section flexible | 0.14 mm² ... 1.5 mm² |
Conductor cross section flexible | 0.14 mm² ... 1.5 mm² (Ferrule with plastic sleeve) |
Conductor cross section flexible | 0.14 mm² ... 1 mm² (Ferrule with plastic sleeve, two conductors on double terminal block) |
Conductor cross section AWG | 26 ... 16 (solid) |
Conductor cross section AWG | 26 ... 16 (flexible) |
Drill hole
Diameter | 3.2 mm |
Width | 31 mm |
Height | 96 mm |
Depth | 75 mm |
Material specifications
Color | gray (RAL 7042) |
Flammability rating according to UL 94 | V2 (Housing) |
Ambient conditions
Degree of protection (Relay base) | IP20 (Relay base) |
Degree of protection (Relay) | RT I (Relay) |
Ambient Temperature (Operation) | -40 °C ... 60 °C |
Ambient temperature (storage/transport) | -40 °C ... 85 °C |
Corrosive gas test
Identification | ISA-S71.04. G3 Harsh Group |
Identification | EN 60068-2-60 |
Standards and Regulations
Standards/regulations | IEC 60947-5-1 |
Mounting
Mounting Type | DIN rail mounting |
Assembly instructions | in rows with zero spacing |
Mounting Position | any |
Accessories
Why Proax for Phoenix Contact 2908332?
Proax is an authorized distributor of Phoenix Contact 2908332 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
Pack Size | 10 |
Recommended