The figure shows the standard item
Official DistributorSKU
MPN
IB IL SGI 2/P/EF-PAC
Weight
0.241 kg
Series IB-IL-SGI
IB IL SGI 2/P/EF-PAC - Analog module
Inline, Strain gauge measurement terminal, transmission speed in the local bus: 500 kbps, 2 precise and fast inputs, 4-, 6-conductor connection technology, degree of protection: IP20, including Inline connectors and marking fields
- 2 high-precision inputs for strain gauges
- Measuring ranges adjusted with nominal characteristic values upon delivery
- Manual entry of characteristic values
- Process data update can be parameterized in increments between 200 µs and 100 ms
- Path adjustment in the process environment
- 2-point adjustment
- Connection of strain gauges in 6- and 4-conductor technology
- Advanced wire-break detection
- Sensor supply of up to 115 mA (8 load cells with 350 Ω per channel)
- Per channel: low-resistance, floating N/O contact
- The channels are parameterized independently of one another via the bus system
- Tara device
- Serial interface for external weight displays
- Status message when zero point is reached and resting of measured value
Technical Specifications
Dimensions
| Width | 48.8 mm |
| Height | 136 mm |
| Depth | 71.5 mm |
Inline local bus
| Connection Method | Inline data jumper |
| Transmission Speed | 500 kbps |
| Transmission physics | Copper |
Serial
| Designation | V.24 (RS-485) serial interface |
| Addressing | Address 1 = Measured gross/net value |
| Addressing | Address 2 = Measured tare value |
| Termination resistor | 120 Ω |
| Transmission protocol | STX/ETX |
Module
| ID code (dec.) | 223 |
| ID code (hex) | DF |
| Length code (hex) | 03 |
| Length code (dec) | 03 |
| Process data channel | 48 bit |
| Input address area | 6 Byte |
| Output address area | 6 Byte |
| Register length | 64 bit |
| Required parameter data | 23 Byte |
| Required configuration data | 5 Byte |
Analog
| Description of the input | Input channels for strain gauge |
| Number of Inputs | 2 |
| Connection technology | 6 or 4-wire, twisted pair shielded cable |
| Bridge difference Ud | Measuring range specified by selecting the characteristic |
| Bridge voltage U0 | 5 V |
| Measured value representation | 16 bit, 20 bit, ASCII data record |
| Characteristics | ±1 mV/V, ±2 mV/V, ±3 mV/V, ±3.33 mV/V, ±4 mV/V, ±5 mV/V, ±6 mV/V, manual characteristic value specification |
Contacts
| Description | Floating N/O contact |
| Quantity | 2 (Ka1-Kb1, Ka2-Kb2) |
| Contact resistance | < 1 Ω (typical) |
| Contact resistance | 3 Ω (maximum) |
| Typical response time | typ. 0.2 ms (opening) |
| Typical response time | typ. 2 ms (close) |
Analog
| Output description | Jumper supply |
| Number of Outputs | 2 |
| Impedance | > 43 Ω (per channel) |
| Output Voltage | typ. 5 V |
| Output Current | max. 115 mA (per channel) |
Product properties
| Product family | Inline |
| Type | modular |
| Scope of delivery | including Inline connectors and marking fields |
| Operating mode | Process data operation with 3 words, PCP with 1 word |
| Special Properties | 2 precise and fast inputs |
| Special Properties | 4-, 6-conductor connection technology |
| Diagnostics messages | Failure of the power supply at UANA Error message in the process data |
| Diagnostics messages | Failure of or insufficient communications power UL I/O error message sent to the bus coupler |
| Diagnostics messages | I/O error Error message in the process data |
Potentials
| Power consumption | typ. 1.4 W (Device in nominal operation) |
| Power consumption | max. 3.5 W (Device with maximum load) |
Potentials: Communications power (UL)
| Supply Voltage | 7.5 V DC (via voltage jumper) |
| Current draw | max. 95 mA |
| Current draw | typ. 80 mA |
Potentials: Supply of analog modules (UANA)
| Supply Voltage | 24 V DC (via voltage jumper) |
| Supply Voltage Range | 19.2 V DC ... 30 V DC (including all tolerances, including ripple) |
| Current draw | typ. 32 mA (in case of typical load of 350 Ohm per channel) |
| Current draw | 115 mA (with maximum load of 43 Ω and display) |
| Current draw | 14 mA (for no-load operation without strain gauge or display) |
Electrical isolation/isolation of the voltage ranges
| Test voltage: Logic | 500 V AC, 50 Hz, 1 min. |
| Test voltage: Analog I/O | 500 V AC, 50 Hz, 1 min. |
| Test voltage: RS-485 | 500 V AC, 50 Hz, 1 min. |
| Test voltage: N/O contact Ka1 - Kb1 | 500 V AC, 50 Hz, 1 min. |
| Test voltage: N/O contact Ka2 - Kb2 | 500 V AC, 50 Hz, 1 min. |
| Test voltage: Functional ground | 500 V AC, 50 Hz, 1 min. |
Connection technology
| Connection name | Inline connector |
Conductor connection
| Connection Method | Spring-cage connection |
| Conductor cross section rigid | 0.08 mm² ... 1.5 mm² |
| Conductor cross section flexible | 0.08 mm² ... 1.5 mm² |
| Conductor cross section AWG | 28 ... 16 |
| Stripping length | 8 mm |
Inline connector
| Connection Method | Spring-cage connection |
| Conductor cross section, rigid | 0.08 mm² ... 1.5 mm² |
| Conductor cross section, flexible | 0.08 mm² ... 1.5 mm² |
| Conductor cross section AWG | 28 ... 16 |
| Stripping length | 8 mm |
Ambient conditions
| Ambient Temperature (Operation) | -25 °C ... 55 °C |
| Degree of Protection | IP20 |
| Air pressure (operation) | 70 kPa ... 106 kPa (up to 3000 m above sea level) |
| Air pressure (storage/transport) | 70 kPa ... 106 kPa (up to 3000 m above sea level) |
| Ambient temperature (storage/transport) | -25 °C ... 85 °C |
| Permissible humidity (operation) | 10 % ... 95 % (non-condensing) |
| Permissible humidity (storage/transport) | 10 % ... 95 % (non-condensing) |
Standards and Regulations
| Protection class | III (IEC 61140, EN 61140, VDE 0140-1) |
Mounting
| Mounting Type | DIN rail mounting |
Accessories
0421029 - Connection terminal block, nom. voltage: 300 V, nominal current: 41 A, connection method: Screw connection, Rated cross section: 4 mm2, cross section: 0.5 mm2 - 6 mm2, mounting: Neutral busbar, color: green-yellow
0421032 - Connection terminal block, nom. voltage: 300 V, nominal current: 41 A, connection method: Screw connection, Rated cross section: 4 mm2, cross section: 0.5 mm2 - 6 mm2, mounting: Neutral busbar, color: black
Why Proax for Phoenix Contact 2702373?
Proax is an authorized distributor of Phoenix Contact 2702373 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
2692351 - Inline analog strain gauge input terminal, two precise inputs, 4, 6-conductor connection method
2878638 - Inline, Strain gauge measurement terminal, transmission speed in the local bus: 500 kbps, 2 fast inputs, 4-, 6-conductor connection technology, degree of protection: IP20, including Inline connectors and marking fields- 2878735 - Inline, Strain gauge measurement terminal, transmission speed in the local bus: 2 Mbps, 2 fast inputs, 4-, 6-conductor connection technology, degree of protection: IP20, including Inline connectors and marking fields
Module Inline d'entrée analogique pour jauge de contrainte, sans accessoire, électronique d'évaluation avec homologation CE
IB IL SCN-8-AC-OCP - Connector, colored identification, for digital Inline terminals, AC voltage
