2865625
Official DistributorSKU
PHX2865625
MPN
MACX MCR-PTB
Weight
0.163 kg
This product is Not Cancellable/Not Returnable
MACX MCR-PTB - Power and error message module
Power and fault signaling module with screw connection, including corresponding ME 17,5 TBUS 1,5/ 5-ST-3,81 GY DIN rail connector
- Simple or redundant supply, decoupled from diode, protected against polarity reversal
- Installation in zone 2 permitted
- Replaceable fuse
- Error message in the event of power supply failure or fuse fault
- Bus cable error message for MACX MCR-...(2)NAM... devices connected via DIN rail connectors
- Relay output (changeover contact) and blinking LED for error messages
- Supply current up to 3.75 A
Technical Specifications
Utilization restriction
| EMC note | EMC: class A product, see manufacturer's declaration in the download area |
Product properties
| Product family | MACX Analog |
Insulation characteristics: GB Standard
| Overvoltage category | II |
| Pollution degree | 2 |
Electrical isolation Supply/switching output
| Electrical isolation | 50 V AC/DC |
Signal
| Voltage input signal | 19.2 V DC ... 30 V DC (24 V DC, -20 % ... +25 %) |
| Fuse | 5 A (replaceable), slow-blow 250 V AC |
| Polarization and surge protection | Yes |
Switching: Relay
| Contact switching type | 1 changeover contact |
| Contact Material | Gold (Au) |
| Maximum Switching Voltage | 50 V AC (2 A) |
| Maximum Switching Voltage | 30 V DC (2 A) |
| Maximum Switching Voltage | 50 V DC (0.22 A) |
Signal
| Max. current output signal | 3.75 A |
| Output Voltage | Input voltage - max 0.8 V at 3.75 A |
Connection data
| Connection Method | Screw connection |
| Stripping length | 7 mm |
| Screw thread | M3 |
| Conductor cross section rigid | 0.2 mm² ... 2.5 mm² |
| Conductor cross section flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross section AWG | 24 ... 14 |
| Tightening torque | 0.5 Nm ... 0.6 Nm |
Ex data
| Ex installation (EPL) | Gc |
| Ex installation (EPL) | Div. 2 |
Signaling
| Status display | 1 x red LED (error) |
| Status display | 2 x green LEDs (PWR1 and PWR2) |
Dimensions
| Width | 17.5 mm |
| Height | 103.6 mm |
| Depth | 113.7 mm |
| Depth NS 35/7,5 | 114.5 mm (Snapped onto DIN rail NS 35/7,5 in accordance with EN 60715) |
Material specifications
| Color | gray (RAL 7042) |
| Flammability rating according to UL 94 | V0 (Housing) |
| Housing Material | Polyamide (PA 6.6) |
Ambient conditions
| Degree of Protection | IP20 (not assessed by UL) |
| Ambient Temperature (Operation) | -40 °C ... 60 °C (Any mounting position) |
| Ambient temperature (storage/transport) | -40 °C ... 80 °C |
| Altitude | ≤ 2000 m |
| Permissible humidity (operation) | 5 % ... 95 % (non-condensing) |
CE
| Certificate | CE-compliant |
ATEX
| Identification | II 3 G Ex ec nC IIC T4 Gc X |
| Certificate | PxCIF08ATEX2865625X |
UKCA Ex (UKEX)
| Identification | II 3 G Ex nA nC IIC T4 Gc X |
| Certificate | PxCIF21UKEX2865625X |
IECEx
| Identification | Ex ec nC IIC T4 Gc |
| Certificate | IECEx IBE 08.0004X |
CCC / China-Ex
| Identification | Ex ec nC IIC T4 Gc |
| Certificate | 2021122303114198 |
UL, USA/Canada
| Identification | UL 61010 Listed |
| Identification | Class I, Div. 2, Groups A, B, C, D T5 |
| Identification | Class I, Zone 2, Group IIC |
Shipbuilding approval
| Certificate | DNV GL TAA00000AG |
EAC Ex
| Identification | 2Ex ec nC IIC T4 Gc |
| Certificate | BY/112 02.01 TP012 103.01 00078 |
DNV GL data
| Temperature | B |
| Humidity | B |
| Vibration | A |
| EMC | B |
| Enclosure | Required protection according to the Rules shall be provided upon installation on board |
EMC data
| Noise immunity | EN 61000-6-2 |
| Note | When being exposed to interference, there may be minimal deviations. |
| Electromagnetic compatibility | Conformance with EMC directive |
| Noise emission | EN 61000-6-4 |
Electromagnetic HF field
| Designation | Electromagnetic RF field |
| Standards/regulations | EN 61000-4-3 |
| Evaluation criterion | A |
Fast transients (burst)
| Designation | Fast transients (burst) |
| Standards/regulations | EN 61000-4-4 |
| Evaluation criterion | A |
Conducted interference
| Designation | Conducted interferences |
| Standards/regulations | EN 61000-4-6 |
| Evaluation criterion | A |
GB Standard
| Standards/regulations | GB 3836.1 |
| Standards/regulations | GB 3836.3 |
| Standards/regulations | GB 3836.8 |
Mounting
| Mounting Type | DIN rail mounting |
Accessories
ME 6,2 TBUS-2 1,5/5-ST-3,81 GY - DIN rail connector (TBUS), 5-pos., for bridging the supply voltage, can be snapped onto NS 35/... DIN rail in accordance with EN 60715
Why Proax for Phoenix Contact 2865625?
Proax is an authorized distributor of Phoenix Contact 2865625 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
MACX MCR-PTB-SP - Power and fault signaling module with Push-in connection, including corresponding ME 17,5 TBUS 1,5/ 5-ST-3,81 GY DIN rail connector
MACX MCR-SL-CAC-12-I-UP - Current measuring transducer for 5 A and 12 A AC, the output signal 0...20 mA or 4...20 mA, can be configured using a DIP switch with an operating mode indication through an LED
MACX MCR-SL-CAC- 5-I - Current measuring transducer for 1 A and 5 A AC, the output signal 0...20 mA or 4...20 mA, can be configured using a DIP switch with an operating mode indication through an LED
MACX MCR-SL-CAC- 5-I-UP - Current measuring transducer for 1 A and 5 A AC, the output signal 0...20 mA or 4...20 mA, can be configured using a DIP switch with an operating mode indication through an LED
MACX MCR-SL-IDSI-I - Output signal conditioner, HART. Isolates and transmits 0/4 - 20 mA signals to a load (I/P converters, regulating valves, displays). Open-circuit detection, SIL 2 in accordance with IEC 61508, screw connection. Replacement item: 2908063 MACX MCR-IDS-I-I.
MACX MCR-SL-IDSI-I-SP, Output signal conditioner, HART. Isolates and transmits 0/4-20 mA signals to a load (I/P converters, control valves, displays). Electrical 3-way isolation, wire break recognition, SIL 2 in accordance with IEC 61508, Push-in connection.
MACX MCR-SL-NAM-2T - NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
MACX MCR-SL-NAM-2RO - NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, screw connection.
MACX MCR-SL-NAM-2RO-SP - NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, Push-in connection.
