Official DistributorSKU
MPN
PSR-M-E1-DO8-PI
Weight
0.156 kg
This product is Not Cancellable/Not Returnable
Series PSR-M-E
PSR-M-E1-DO8-PI - Extension module
Extension module with 8 signal outputs, TBUS interface, plug-in Push-in terminal block, TBUS connector included
- Cost-effective safety solution with a high level of adaptability to individual requirements
- Fast startup, thanks to easy hardware and software configuration
- Machine downtimes minimized with comprehensive, easy-to-understand diagnostics
- Tool-free and time-saving installation thanks to Push-in technology
- Narrow housing width of just 22.6 mm
Technical Specifications
Product properties
| Application | Extension module |
Insulation characteristics
| Protection class | III (EN 50178) |
Times
| Response time | see user manual |
| Restart time | min. 5 s (Boot time) |
| Restart time | max. 10 s (Boot time) |
Electrical properties
| Maximum power dissipation for nominal condition | 1.82 W (with max. permissible load) |
| Nominal operating mode | 100% operating factor |
| Interfaces | DIN rail TBUS for connection to the master module, supplied as standard |
Air clearances and creepage distances between the power circuits
| Rated Insulation Voltage | 250 V AC |
| Rated surge voltage/insulation | Basic insulation 4 kV between all current paths and housing |
Supply
| Designation | A1/A2 |
| Rated control circuit supply voltage US | 19.2 V DC ... 28.8 V DC |
| Rated control circuit supply voltage US | 24 V DC -20 % / +20 % (external fuse, typically 4 A) |
| Rated control supply current IS | typ. 20 mA |
| Power consumption at US | typ. 0.48 W |
| Inrush Current | 1.5 A (Δt = 1 ms at Us) |
| Filter time | typ. 5 ms (at A1 in the event of voltage dips at Us) |
| Protective circuit | Serial protection against polarity reversal |
| Protective circuit | Suppressor diode |
| Designation | 24V/A2 |
| Rated control circuit supply voltage US | 24 V DC -20 % / +20 % (external fuse, typically 4 A) |
| Rated control supply current IS | typ. 20 mA (Outputs active, without load) |
| Inrush Current | 2 A (Δt = 1 ms at Us) |
| Filter time | typ. 1 ms (in the event of voltage dips) |
| Protective circuit | Inverse-parallel protection against polarity reversal |
| Protective circuit | Suppressor diode |
Signal: MO1, MO2, MO3, MO4, MO5, MO6, MO7, MO8
| Output description | PNP, IEC 61131-2 Typ 0,1 |
| Output description | non-safety-related |
| Output description | Reference ground A2 |
| Number of Outputs | 8 |
| Output voltage when switched off | max. 0.1 V |
| Voltage | 24 V DC (via 24 V) |
| Maximum Inrush Current | 1.1 A (Δt = 3 s at Us) |
| Limiting Continuous Current | 100 mA (per channel) |
| Limiting Continuous Current | 400 mA (Total current of all digital signal outputs) |
| Leakage current | max. 100 µA |
| Switching frequency | max. 1/4 x tCycle [Hz] |
| Protective circuit | Suppressor diode |
| Short-circuit protection | Yes (self-limitation at 1.1 A) |
| Cable Length | max. 100 m (per output) |
Connection technology
| pluggable | yes |
Conductor connection
| Connection Method | Push-in connection |
| Conductor cross section rigid | 0.2 mm² ... 2.5 mm² |
| Conductor cross section flexible | 0.2 mm² ... 2.5 mm² |
| Conductor cross-section AWG | 24 ... 14 |
| Stripping length | 10 mm |
Signaling
| Status display | 1 x LED (green), 2 x LED (orange) |
| Status display | 8 x LED (yellow) |
| Operating voltage display | 1 x green LED |
| Error indication | 2 x LED (red) |
Dimensions
| Width | 22.61 mm |
| Height | 107.74 mm |
| Depth | 113.6 mm |
Material specifications
| Color (Housing) | yellow (RAL 1018) |
| Housing Material | Polyamide PA non-reinforced |
Ambient conditions
| Degree of Protection | IP20 |
| Min. degree of protection of inst. location | IP54 |
| Ambient Temperature (Operation) | -10 °C ... 55 °C (observe derating) |
| Ambient temperature (storage/transport) | -20 °C ... 85 °C |
| Maximum altitude | ≤ 2000 m (Above sea level) |
| Max. permissible humidity (storage/transport) | 95 % (non-condensing) |
| Max. permissible relative humidity (operation) | 95 % (non-condensing) |
| Shock | 10g for Δt = 16 ms (continuous shock, 1000 shocks in each space direction) |
| Vibration (Operation) | 10 Hz ... 150 Hz, 2g |
Air clearances and creepage distances between the power circuits
| Standards/regulations | EN 50178 |
Mounting
| Mounting Type | DIN rail mounting |
| Assembly instructions | Observe derating |
| Mounting Position | vertical or horizontal |
Accessories
Why Proax for Phoenix Contact 1105133?
Proax is an authorized distributor of Phoenix Contact 1105133 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
PSR-M-E1-DO8-SC - Extension module with 8 signal outputs, TBUS interface, plug-in screw terminal block, TBUS connector included
PSR-M-E2-DO16-PI - Extension module with 16 signal outputs, TBUS interface, plug-in Push-in terminal block, TBUS connector included
PSR-M-E2-DO16-SC - Extension module with 16 signal outputs, TBUS interface, plug-in screw terminal block, TBUS connector included
