Official DistributorSKU
MPN
2861632
Weight
0.164 kg
This product is Not Cancellable/Not Returnable
Series IB-IL-PWM
IB IL PWM/2-PAC - Function module
Inline function terminal for pulse width and frequency modulation or activation of impulse-driven motor control parts with pulse/direction interface, two outputs for 5 V or 24 V
- 2 independent channels
- Output of 5 V or 24 V signals
- Maximum frequency of 50 kHz
- Pulse direction signal output without integrated ramp function for controlling step motor power supply units
- Single pulse output (pulse length of 10 μs to 25.5 s can be set)
- Pulse width modulation (period length can be set in increments from 100 µs to 10 s, duty factor in 0.39% increments)
- Frequency output (frequency can be set between 0 Hz and 50 kHz)
Technical Specifications
Dimensions
| Width | 24.4 mm |
| Height | 136.8 mm |
| Depth | 71.5 mm |
Inline local bus
| Number of interfaces | 2 |
| Connection Method | Inline data jumper |
| Transmission Speed | 500 kbps |
Module
| ID code (dec.) | 191 |
| ID code (hex) | BF |
| Length code (hex) | 02 |
| Length code (dec) | 02 |
| Process data channel | 32 bit |
| Input address area | 4 Byte |
| Output address area | 4 Byte |
| Register length | 4 Byte |
| Required parameter data | 1 Byte |
| Required configuration data | 5 Byte |
Digital:
| Output name | Digital output: 24 V DC |
| Connection technology | 2-conductor (shielded) |
| Number of Outputs | 2 |
| Protective circuit | Short-circuit protection, overload protection of the outputs; integrated damping diode for each channel |
| Output Voltage | 24 V |
| Maximum output current per module / terminal block | 1 A |
| Nominal Output Voltage | 24 V DC |
| Nominal load, inductive | 12 VA (1.2 H, 24 Ω) |
| Nominal load, lamp | 12 W |
| Nominal load, ohmic | 12 W |
| Maximum operating frequency with ohmic nominal load | 500 Hz |
| Reverse voltage resistance to short pulses | Reverse voltage proof |
| Behavior with overload | Auto restart |
| Behavior at voltage switch-off | The output follows the power supply without delay |
| Overcurrent shut-down | as of 0.7 A |
| Output name | Digital output: 5 V DC |
| Connection technology | 2-conductor (shielded) |
| Number of Outputs | 2 |
| Protective circuit | Short-circuit protection, overload protection of the outputs; integrated damping diode for each channel |
| Nominal Output Voltage | 5 V DC |
| Maximum operating frequency with ohmic nominal load | 50 kHz |
Product properties
| Product family | Inline |
| Type | modular |
| Operating mode | PWM, frequency generator, single-shot, pulse/direction signal |
| Operating mode | Process data operation with 2 words |
| Diagnostics messages | Short circuit or overload of a 24 V output yes |
Potentials: Communications power (UL)
| Supply Voltage | 7.5 V DC (via voltage jumper) |
| Current draw | max. 130 mA |
| Power consumption | max. 0.98 W |
Potentials: Segment circuit supply (US)
| Supply Voltage | 24 V DC (via voltage jumper) |
| Current draw | max. 1 A |
| Current draw | 0 A |
Electrical isolation/isolation of the voltage ranges
| Test voltage: 7.5 V supply (bus logics)/24 V supply (I/O) | 500 V AC, 50 Hz, 1 min. |
| Test voltage: 7.5 V supply (bus logic) / 5 V supply (I/O) | 500 V AC, 50 Hz, 1 min. |
| Test voltage: 24 V supply (I/O) / functional ground | 500 V AC, 50 Hz, 1 min. |
| Test voltage: 5 V supply (I/O)/functional ground | 500 V AC, 50 Hz, 1 min. |
Connection technology
| Connection name | Inline connector |
Conductor connection
| Connection Method | Spring-cage connection |
| Conductor cross section rigid | 0.08 mm² ... 1.5 mm² |
| Conductor cross section flexible | 0.08 mm² ... 1.5 mm² |
| Conductor cross section AWG | 28 ... 16 |
| Stripping length | 8 mm |
Inline connector
| Connection Method | Spring-cage connection |
| Conductor cross section, rigid | 0.08 mm² ... 1.5 mm² |
| Conductor cross section, flexible | 0.08 mm² ... 1.5 mm² |
| Conductor cross section AWG | 28 ... 16 |
| Stripping length | 8 mm |
Ambient conditions
| Ambient Temperature (Operation) | -25 °C ... 55 °C |
| Degree of Protection | IP20 |
| Air pressure (operation) | 70 kPa ... 106 kPa (up to 3000 m above sea level) |
| Air pressure (storage/transport) | 70 kPa ... 106 kPa (up to 3000 m above sea level) |
| Ambient temperature (storage/transport) | -25 °C ... 85 °C |
| Permissible humidity (operation) | 10 % ... 95 % (non-condensing) |
| Permissible humidity (storage/transport) | 10 % ... 95 % (non-condensing) |
Standards and Regulations
| Protection class | III (IEC 61140, EN 61140, VDE 0140-1) |
Mounting
| Mounting Type | DIN rail mounting |
Accessories
Why Proax for Phoenix Contact IB IL PWM/2-PAC?
Proax is an authorized distributor of Phoenix Contact IB IL PWM/2-PAC and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Alternate Names | IBILPWM2PAC |
| Pack Size | 1 |
Recommended
2742612 - Inline function terminal for pulse width and frequency modulation or activation of impulse-driven motor control parts with pulse/direction interface, two outputs for 5 V or 24 V
2860620 - Connector set, for power terminal block, copper, colored identification.
2702501 - Inline, Temperature measurement terminal, Analog RTD inputs: 4 (Pt 1000), connection technology: 2-conductor, transmission speed in the local bus: 500 kbps, degree of protection: IP20, including Inline connector
2702499 - Inline, Temperature measurement terminal, Analog RTD inputs: 4 (Pt 100), connection technology: 2-conductor, transmission speed in the local bus: 500 kbps, degree of protection: IP20, including Inline connector
1185434 - Inline, Temperature measurement terminal, Analog RTD inputs: 4 (NTC, linear resistors), connection technology: 2-conductor, transmission speed in the local bus: 500 kbps, degree of protection: IP20, including Inline connector
2700965 - Inline power measurement terminal for direct measurement of AC currents up to 5 A, including neutral conductor current and phase conductor voltages up to 400 V AC (phase/neutral conductor) or 690 V AC (phase/phase) complete with accessories (connectors and labeling fields)
2878476 - Adapter cable for the connection of the field multiplexer to the PSI-MOS interface module
2819309 - Inline measurement terminal for absolute encoders, without accessories, 1 input for absolute rotation or position measurement systems, with SSI interface- 2819574 - Inline measurement terminal block for absolute encoders, complete with accessories (connector and labeling field), 1 input for absolute rotation or position measurement systems, with SSI interface
2861865 - Inline positioning terminal, complete with accessories, 1 absolute encoder input, 4 digital inputs 24 V DC, 4 digital outputs 24 V DC, 500 mA, 3-conductor connection technology
2836340 - Inline positioning terminal, without accessories, 1 absolute encoder input, 4 digital inputs 24 V DC, 4 digital outputs 24 V DC, 500 mA, 3-conductor connection technology
