Popular Brands in { name }

Discover { name } at Proax - Canada's top automation distributor. Easy pick-up, fast shipping. Explore now.

Shop { name } Online

**Here are some possible reasons why:**
- You may’ve typed the wrong search term, such as a misspelled product name or special characters/symbols.
- We might not carry the product you're looking for

Please try refining your search by not using special characters.

**Are these not the issues? Feel free to contact us and we'll assist you as quickly as possible.**

Search

Maximum Operating Voltage UL/CSA

Main Circuit 600 V AC

Main Circuit 250 V AC

Auxiliary Circuit 250 V AC/DC

Number of Poles

Rated Operational Voltage

690 V AC

Main Circuit 690 V AC

600 V DC

Main Circuit 690 V

250 V DC

Main Circuit 250 V DC

250 V

Suitable for Product Class

Manual Motor Starter

Terminal Type

Screw Terminals

Push-in Spring Terminals

Omron

Cr101 Manual Motor-starting switches are designed for use with self-protected 1Ph & 3Ph motors, ON/OFF applications where overload protection is not required. 2HP//240Vac

CR101X4

CR101X5

CR101X6

CR101X8

CR101Y400J

S1-PB1-25 power infeed block allows the connection of cable cross sections up to 25mm² and is usable with MS116 or MS132. This allows the easy and fast connection for single-phase applications, especially for MS132-(K)T for control transformer protection. The rated current is 32 A.

S1-PB1-25

S1-PB1-25 1-phase power infeed block for MS116 / MS132 / MS132-T, 25mm2, IEC

MS132-K Manual Motor Starters with Push-in Spring terminals are approved as Self-Protected Combination Motor Controllers (Type E) acc. to UL60947-4-1. For this air clearance and creepage distances on the line side of MS132 must be increased, which can be achieved by mounting TS1-K terminal spacers.

TS1-M3-K

TS1-M3-K Terminal Spacer MS132-K For MS132-0.16K - MS132-32K Type E

Signaling contacts SK1-AR with screw terminals signal the tripping of the manual motor starter.
For SK1-AR a red flag in a window on the front of the device indicates the tripping event. The contact positions of SK1-AR don't need to be manually reset after a tripping. They are reset to their original position when the manual motor starter is switched back on. The SK1-AR signaling contacts signal tripping regardless if it was caused by short-circuit, overload or electrical release (AA1 or UA1). They are attached on the right side of the manual motor starter. Signaling contacts SK1-AR are available as normally open or normally closed contacts.

SK1-02AR

SK1-02AR Signaling Contact, 2NC with screw terminals

Signaling contacts SK1-ARK with Push-in spring terminals signal the tripping of the manual motor starter. For SK1-ARK a red flag in a window on the front of the device indicates the tripping event. The contact positions of SK1-AR don't need to be manually reset after a tripping. They are reset to their original position when the manual motor starter is switched back on. The SK1-ARK signaling contacts signal tripping regardless if it was caused by short-circuit, overload or electrical release (AA1 or UA1). They are attached on the right side of the manual motor starter. Signaling contacts SK1-ARK are available as normally open or normally closed contacts.

SK1-02ARK

SK1-02ARK Signaling Contact, 2NC with Push-in Spring terminals

SK1-11ARK

SK1-11ARK Signaling Contact, 1NO+1NC with Push-in Spring terminals

SK1-20ARK

SK1-20ARK Signaling Contact, 2NO with Push-in Spring terminals

S2-M3-50 three phase feeder terminals allow the connection of cable cross sections up to 50mm². They are usable with MS165 manual motor starters. The rated current is 125 A (IEC) / 120 A (UL).

S2-M3-50

S2-M3-50 3-phase Power infeed Block for MS165, 50 mm²

The J7MC Manual Motor Starter allows you to manually turn On/Off the motor while having fuse-less protection against short-circuit, overload and phase failures. Recommended to use with J7KC contactor.<ul>
<li>On/Off control</li>
<li>Best matched for AC-3 Class motor drive</li>
<li>W x D x H (45mm X 46mm  x67.5 mm)</li>
<li>In combination with magnetic contactor model J7KC, it is ideal for control of motors to AC-3 class, 2.2 kW (200 to 240 VAC) * or 5.5 kW (380 to 440 VAC)</li>
<li>Rocker switch (standard type) and rotary switch (high-performance type)</li>
<li>High breaking capacity (Max100 kA/440 VAC)</li>
<li>Equipped with a dial cover as standard to protect accidental setting changes. Lockable with a padlock to ensure safety at startup</li>
<li>Certified as compliant with the main safety standard</li>
<li>Push-In Plus wiring technology saves wiring and maintenance time</li>
</ul>
