Démarreurs manuels

Cr101 Manual Motor-starting switches are designed for use with self-protected 1Ph & 3Ph motors, ON/OFF applications where overload protection is not required. 2HP//240Vac

Cr101 Manual Motor-starting switches are designed for use with self-protected 1Ph & 3Ph motors, ON/OFF applications where overload protection is not required. 2HP//240Vac

Cr101 Manual Motor-starting switches are designed for use with self-protected 1Ph & 3Ph motors, ON/OFF applications where overload protection is not required. 2HP//240Vac

Cr101 Manual Motor-starting switches are designed for use with self-protected 1Ph & 3Ph motors, ON/OFF applications where overload protection is not required. 2HP//240Vac

Cr101 Manual Motor-starting switches are designed for use with self-protected 1Ph & 3Ph motors, ON/OFF applications where overload protection is not required. 2HP//240Vac

S1-PB1-25 power infeed block allows the connection of cable cross sections up to 25mm² and is usable with MS116 or MS132. This allows the easy and fast connection for single-phase applications, especially for MS132-(K)T for control transformer protection. The rated current is 32 A.

MS132-K Manual Motor Starters with Push-in Spring terminals are approved as Self-Protected Combination Motor Controllers (Type E) acc. to UL60947-4-1. For this air clearance and creepage distances on the line side of MS132 must be increased, which can be achieved by mounting TS1-K terminal spacers.

Signaling contacts SK1-AR with screw terminals signal the tripping of the manual motor starter.For SK1-AR a red flag in a window on the front of the device indicates the tripping event. The contact positions of SK1-AR don't need to be manually reset after a tripping. They are reset to their original position when the manual motor starter is switched back on. The SK1-AR signaling contacts signal tripping regardless if it was caused by short-circuit, overload or electrical release (AA1 or UA1). They are attached on the right side of the manual motor starter. Signaling contacts SK1-AR are available as normally open or normally closed contacts.

Signaling contacts SK1-ARK with Push-in spring terminals signal the tripping of the manual motor starter. For SK1-ARK a red flag in a window on the front of the device indicates the tripping event. The contact positions of SK1-AR don't need to be manually reset after a tripping. They are reset to their original position when the manual motor starter is switched back on. The SK1-ARK signaling contacts signal tripping regardless if it was caused by short-circuit, overload or electrical release (AA1 or UA1). They are attached on the right side of the manual motor starter. Signaling contacts SK1-ARK are available as normally open or normally closed contacts.

Signaling contacts SK1-ARK with Push-in spring terminals signal the tripping of the manual motor starter. For SK1-ARK a red flag in a window on the front of the device indicates the tripping event. The contact positions of SK1-AR don't need to be manually reset after a tripping. They are reset to their original position when the manual motor starter is switched back on. The SK1-ARK signaling contacts signal tripping regardless if it was caused by short-circuit, overload or electrical release (AA1 or UA1). They are attached on the right side of the manual motor starter. Signaling contacts SK1-ARK are available as normally open or normally closed contacts.

Signaling contacts SK1-ARK with Push-in spring terminals signal the tripping of the manual motor starter. For SK1-ARK a red flag in a window on the front of the device indicates the tripping event. The contact positions of SK1-AR don't need to be manually reset after a tripping. They are reset to their original position when the manual motor starter is switched back on. The SK1-ARK signaling contacts signal tripping regardless if it was caused by short-circuit, overload or electrical release (AA1 or UA1). They are attached on the right side of the manual motor starter. Signaling contacts SK1-ARK are available as normally open or normally closed contacts.

S2-M3-50 three phase feeder terminals allow the connection of cable cross sections up to 50mm². They are usable with MS165 manual motor starters. The rated current is 125 A (IEC) / 120 A (UL).