Hollow Rotary Actuator
Official DistributorSKU
The DGII Series uses a highly rigid hollow rotary table with a efficient and energy saving AlphaStep AR Series closed loop motor and driver package allowing for highly accurate positioning of larger inertia loads. The built-in controller (stored data) allows for easy networking and simplified multi-axis control.Controller connection options: 1: I/O, 2: Modbus (RTU/RS-485) or 3: FA Network (network converter)Large-Diameter, Hollow Output TableDirect CouplingAccurate PositioningShorter Positioning TimeEasy Home OperationDesigned for Continuous Operation*Connection cables required (sold separately).
Technical Specifications
| Frame Size | 7.87 in |
| Power Supply | Single-Phase 100-120 VAC |
| Shaft | Single |
| Electromagnetic Brake | Not Equipped |
| Output Table Supporting Bearing | Cross-Roller Bearing |
| Permissible Torque | 440 lb-in |
| Inertia | 916400x10-7 kg·m² |
| Permissible Speed (r/min) | 110 |
| Gear Ratio (X:1) | 18 :1 |
| Max. Holding Torque | 310 lb-in |
| Resolution (Resolution Setting: 1000 P/R) | 18000 P/R (0.02º) |
| Frequency | 50/60 Hz |
| Input Current | 5.90 A |
| Control Power Supply | 24 VDC ±5% 0.5 A |
| Repetitive Positioning Accuracy (arc sec) | ±15 arc sec (±0.004º) |
| Lost Motion | 2 arc minute (0.033°) |
| Angular Transmission Accuracy | 2 arc minute (0.033º) |
| Permissible Thrust Load | 4000 N |
| Permissible Moment Load | 100 N·m |
| Runout of Output Table Surface | 0.015 mm |
| Runout of Output Table Inner (Outer) Diameter | 0.030 mm |
| Parallelism of Output Table | 0.050 mm |
| Degree of Protection | [Actuator] IP40 (IP20 for motor connector) |
| Insulation Class | 130 (B) |
| Insulation Resistance (Actuator) | 100 MΩ minimum when measured by a 500 VDC megger between the Case - Motor and Sensor Windings |
| Insulation Resistance (Driver) | 100 M Ω minimum when measured by a 500 VDC megger between the PE Terminal - Power Input Terminal |
| Dielectric Strength (Actuator) | No abnormality is found with the following application for 1 minute: Case - Motor and Sensor Windings 1.5 kV, 50 Hz or 60 Hz |
| Dielectric Strength (Driver) | No abnormality is found with the following application for 1 minute: PE Terminal - Power Supply Terminal 1.8 kV, 50 Hz or 60 HzSignal I/O Terminal - Power Supply Terminal 1.9 kV, 50 Hz or 60 Hz |
| Ambient Temperature (Actuator) | 0 ~ +50ºC (+32 ~ 122ºF)(non-freezing)0 ~ +40ºC (+32 ~ 104ºF)(non-freezing) when home-sensor set (accessory is attached) |
| Ambient Temperature (Driver) | 0 ~ +55ºC (+32 ~ 131ºF)(non-freezing) |
| Ambient Humidity | 85% max. (non-condensing) |
| Operating Atmosphere | Use in an area without corrosive gases and dust. The product should not be exposed to water, oil or other liquids. |
| Safety Standards | CE |
| RoHS Compliant | Yes |
| Components | ARD-AD (Driver) |
| Number of Positioning Data Sets | 64 Points |
| Positioning Operation | Independent, Linked, Linked 2, Sequential, Direct |
| Protocol | Modbus Protocol (Modbus RTU mode) |
| Electrical Characteristics | EIA-485 basedUse twisted-pair wire (TIA/EIA-568B CAT5e or greater recommended), and set a max. total length of 50 m (164 ft.) |
| Transmission/Reception Mode | Half-duplex communication |
| Baud Rate | 9600 bps/19200 bps/57600 bps/115200 bps |
| Physical Layer | Start-stop synchronization mode (Data: 8-bits, stop bit: 1-bit/2-bit, parity: none/even numbers/odd numbers) |
| Connection Type | Up to 31 units can be connected to one programmable controller (master equipment). |
Why Proax for Oriental Motor DGM200R-ARAC / ARD-AD?
Proax is the authorized distributor of Oriental Motor DGM200R-ARAC / ARD-AD. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Alternate Names | DGM200RARACARDAD |
| Pack Size | 1 |
Recommended
