SCM425UA-120 / DSCD25UA
Official DistributorSKU
ORIDSCI425UA1203V
The DSC Series features AC motors and speed controllers that utilized Oriental Motor's exclusive technology.Closed Loop Control for High ReliabilityEasy Installation and Simple Data SettingCompact Motor and Controller (with Capacitor)
Technical Specifications
| Motor Type | AC Motor |
| Motor | Induction |
| Frame Size | 3.15 in |
| Output Power | 25 W (1/30 HP) |
| Power Supply | Single-Phase 110/115 VAC |
| Frequency (Hz) | 60 |
| Current | 0.75 A |
| Control Power Source | 24 VDC ±10% 0.15 A or more |
| Shaft/Gear Type | Parallel Shaft Gearhead |
| Gear Ratio (X:1) | 120 :1 |
| Output Shaft Diameter | 15 mm |
| Electromagnetic Brake | Not Equipped |
| Permissible Torque | 141 lb-in |
| Variable Speed Range (r/min) | 0.75 ~ 13.3 |
| Permissible Load Inertia | 49000 oz-in² |
| Permissible Overhung Load | 0.39 in. from Shaft End = 101 lb |
| Permissible Thrust Load | 22 lb |
| RoHS Compliant | These products do not contain substances that exceed the regulation values in the RoHS Directive. |
| Safety Standards | c-UL |
| CE Marking | Low Voltage Directives |
| Insulation resistance | [Controller] 100 MΩ or more when measured by a 500 VDC between the main circuit terminal and the control circuit terminal, between the main circuit terminal and the case and between the main circuit terminal and FG after continuous operation under normal ambient temperature and humidity. |
| Dielectric strength | [Controller] Sufficient to withstand 1.9 kVAC at 50 Hz or 60 Hz applied between the main circuit terminal and the control circuit terminal, and between the main circuit terminal and the case, and 1.5 kVAC at 50 Hz or 60 Hz applied between the main circuit terminal and FG for 1 minute after continuous operation under normal ambient temperature and humidity. |
| Temperature Rise | A gearhead or equivalent heat sink is connected to the motor and the winding temperature rise is measured at 144ºF (80ºC) or less using the resistance change method after rated operation with no load under normal ambient temperature and humidity. |
| Overheat Protection Device | Built-in Thermal Protector (automatic return type) |
| Ambient temperature range | [Controller] 32ºF ~ 122ºF (0ºC ~ 50ºC) |
| Ambient Humidity | 85% max. (non-condensing) |
| Altitude | Max. of 1000 m (3300 ft.) above sea level |
| Thermal Class | 130 (B) |
| Degree of Protection | IP20 |
| Speed Control Method (Select one of the following) | Setting via control panel (A maximum of 4 patterns of operating data can be set) |
| Acceleration/Deceleration Time Setting Range | 0.0 ~ 15.0 secondsAcceleration/deceleration time varies with the load condition of the motor. |
| Monitoring Mode | Speed, operating data number, alarm code, warning code, I/O monitor |
| Data Mode | Speed, acceleration time, deceleration time, reset |
| Parameter Mode | Gear ratio, speed increasing ratio, fixed last digit display, initial operation inhibition alarm, external speed command input, external speed command voltage selection, external speed command offset, speed upper and lower limit, input function selection, output function selection, motor lock detection time, motor rotation direction, reset |
| Test Mode | JOG Operation |
| Other Function | Lock data editing |
| Input Signals | Photocoupler Input Input resistance 4.7 kΩArbitrary signal assignment to IN0 ~ IN5 input (6 points) is possible [ ]: Initial setting[FWD], [REV], [M0], [M1], [ALARM-RESET], [FREE], EXT-ERRORSink Input/Source Input…Can be switched using the selection switch: Factory setting sink input |
| Output Signals | Photocoupler and Open-Collector Output External power supply: 4.5~30 VDC 40 mA max.Arbitrary signal assignment to OUT0, OUT1 output (2 points) is possible [ ]: initial settingSink Output/Source Output…Supports external wiring |
| Protective Function | When the following protective functions are activated, the motor will coast to a stop, and the ALARM output will be turned off. At the same, the alarm code will be displayed on the control panel and the ALARM LED will illuminate.Alarm Types: Motor overheat, motor lock, overspeed, EEPROM error, initial operation inhibition, external stop |
Why Proax for Oriental Motor SCM425UA-120 / DSCD25UA?
Proax is the authorized distributor of Oriental Motor SCM425UA-120 / DSCD25UA. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Alternate Names | SCM425UA120DSCD25UA |
| Pack Size | 1 |
Recommended
