The figure shows version HC-B 24-ADP-VC...
Official DistributorSKU
MPN
HC-B 16-ADP-VC-1
Weight
0.069 kg
This product is Not Cancellable/Not Returnable
Series HC-B
HC-B 16-ADP-VC-1 - Adapter plate
Adapter plates 2 mm thick, for panel cutouts of HC-B 16 size, including 1.5 mm flat gasket, size 1
Technical Specifications
Safety note
| Safety note | WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. |
| Safety note | • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. |
| Safety note | • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. |
| Safety note | • The products are suitable for applications in plant, controller, and electrical device engineering. |
| Safety note | • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. |
| Safety note | • Assembled products may not be manipulated or improperly opened. |
| Safety note | • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). |
| Safety note | • When using the product in direct connection with third-party manufacturers, the user is responsible. |
| Safety note | • For operating voltages > 50 V AC, conductive connector housings must be grounded |
| Safety note | • Ensure that the protective or functional ground has been properly connected. |
| Safety note | • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector |
| Safety note | • Observe the corresponding technical data. You will find information:o On the producto On the packing labelo In the supplied documentationo Online at phoenixcontact.com/products under the product |
| Safety note | • Only use tools recommended by Phoenix Contact |
| Safety note | • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. |
| Safety note | • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products |
| Safety note | • Operate the connector only when it is fully plugged in. |
| Safety note | • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. |
| Safety note | • Observe the minimum bending radius of the cable. Lay the cable without twisting it. |
| Safety note | • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). |
Product properties
| Product family | VARIOCON |
| Type | VC1 |
| Seal present | yes |
Dimensions
| Width | 114 mm |
| Height | 43 mm |
| Length | 3.5 mm |
Material specifications
| Material | V2A |
| Material | Stainless steel 1.4301/AISI 304 |
| Seal material | Neoprene |
Ambient conditions
| Degree of Protection | IP65 (DIN IEC 60529) |
| Degree of Protection | IP65 |
Why Proax for Phoenix Contact 1885758?
Proax is an authorized distributor of Phoenix Contact 1885758 and one of Phoenix Contact's largest distributors in North America. Our highly skilled in-house technical team is ready to assist with any technical needs.
Have a question in mind? to help you get the right product as quickly as possible for your project. We're always here to help!
Short Lead Time
Highly Trained Staff
Live Chat
Technical Support
Local Inventory
60+ Years Experience
Additional Information
| Pack Size | 1 |
Recommended
1885761 - Adapter plates 2 mm thick, for panel cutouts of HC-B 16 size, including 1.5 mm flat gasket, size 1- 1885774 - Adapter plates 2 mm thick, for panel cutouts of HC-B 16 size, including 1.5 mm flat gasket, size 1
- 1885800 - Adapter plates 2 mm thick, for panel cutouts of HC-B 16 size, including 1.5 mm flat gasket, size 3
- 1885790 - Adapter plates, 2 mm thick, for HC-B 16 size panel cutouts, including 1.5 mm flat gasket, size 2
- 1885787 - Adapter plates 2 mm thick, for panel cutouts of HC-B 16 size, including 1.5 mm flat gasket, size 1
1585207 - D-SUB adapter plate, for one D-SUB connector, no. of positions 37, housing series HC-B 16...
1775541 - D-SUB adapter plate, for two D-SUB connectors, no. of positions 50, housing series HC-B 16...- 1775525 - D-SUB adapter plate, for two D-SUB connectors, no. of positions 37, housing series HC-B 16...
- 1775538 - D-SUB adapter plate, for one D-SUB connector, no. of positions 50, housing series HC-B 16...
- 1775512 - D-SUB adapter plate, for one D-SUB connector, no. of positions 37, housing series HC-B 16...
1771600 - HEAVYCON B16 panel mounting base, for double locking latch, height: 29 mm, with plastic cover, with flat gasket
1642742 - HEAVYCON panel mounting base B16, with double locking latch, EMC version. Not suitable for D series terminal adapters
1605200 - HEAVYCON panel mounting base B16, with double locking latch made of sheet steel, height 27 mm, with flat gasket
1585692 - HEAVYCON panel mounting base B16, with single locking latch made of sheet steel, height 27 mm, with flat gasket
1771587 - HEAVYCON B16 panel mounting base, with double locking latch, height: 29 mm, with flat gasket
1771590 - HEAVYCON B16 panel mounting base, with single locking latch, height: 29 mm, with flat gasket
1771613 - HEAVYCON B16 panel mounting base, with single locking latch, height: 29 mm, with plastic cover, with flat gasket
1585540 - HEAVYCON panel mounting base B16, with single locking latch made of sheet steel, height 27 mm, with plastic cover, with flat gasket
Embase B16, avec étrier longitudinal, matériau: Aluminium coulé sous pression, Matériau du capot de protection: Al, hauteur: 29 mm, presse-étoupe: sans, capot de protection: oui, Standard, avec joint plat
