Contrôleurs de moteur

CDP24.150 Cable SMK3.0 - Drawer unshielded, length 1.5 m. Used as connection from the drawer terminal in the back to the SMK3.0 single mounting kit. 5-pole terminal block included.

External current transformer for currents up to 500 A primary side. The secondary side is feed to the UMC100.3 motor controller. This enables the UMC100.3 to see up to the primary current.

External current transformer for currents up to 850 A primary side. The secondary side is feed to the UMC100.3 motor controller. This enables the UMC100.3 to see up to the primary current.

This SMK3.0 mounting kits allow to mount EIU32.0, PNU32.0, DNP31.0, MRP31.0, PDR31.0 and PDP32.0. The SMK3.0 mounting kit itself can be placed outside of the drawers, for example in the cable compartment.

SMK3-X2.10 is a terminal block 2-pole for SMK3.0 power supply connection. Normally included in SMK3.0 package. (spare parts)

SMK3-X1.10 is a terminal block 5-pole for SMK3.0 communication connection. Normally included in CDP cable order. (spare parts)

The MRP31.0 device allows the connection of the Universal Motor Controller UMC100.3 to a Modbus RTU network. It can be mounted directly onto the UMC100.3 or on the SMK3.0 mounting kit.

The UMCPAN-CAB is a control panel cable and a mounting kit for use in drawer applications. It connects the panel, which is mounted on the drawer front with the UMC100.3 inside of the drawer. This cable is 1.5 m long.

CDP18-FBP.150 Cable ETH-X1/X4-open wire unshielded, length 1.5 m. Used as connection from the UMC100.3 motor controller to the drawer terminal in the back.

AI111.0 AI111.0 Analog Input-Module for UMC100, 3 inputs PT100, PT100, KTY83, KTY84, NTC, Supply 24 V DC. Two analogue extension modules can be connected at the same time.

The UTP22-FBP allows to configure and monitor multiple UMC100.3 devices connected to a PROFIBUS network from a service laptop via FIM software.

The UMC100.3 demo case TBU22-FBP.0 is a ready made demo kit that allows to demonstrate and test a wide range of UMC100.3 functions. The demo case can be supplied with 110 V AC or 230 V AC.

Set of all terminal blocks for the UMC100.3 DC versions, including terminal blocks for DI, DO, PTC, Data connection.

CEM11-FBP.35 Earth Leakage Monitor features a 35 mm diameter through hole. A threshold can be set, upon violation of this threshold a binary signal is outputted.

CEM11-FBP.60 Earth Leakage Monitor features a 60 mm diameter through-hole. A threshold can be set, upon violation of this threshold a binary signal is outputted.

CEM11-FBP.120 Earth Leakage Monitor features a 120 mm diameter through-hole. A threshold can be set, upon violation of this threshold a binary signal is outputted.

The intelligent motor controller UMC100.3 DC uses a 24 V DC supply and is suitable to protect against overload. It can be connected to a variety of communication networks and has a wide range of additional parameters to maximize motor protection.

The DNP31.0 communication interface is an optional device for the UMC100.3 which enables the connection of the UMC100.3to a DeviceNet system. It can be mounted directly onto the UMC100.3 or on the SMK3.0 mounting kit.

Voltage expansion module for UMC100. Also for use in IT networks. With this module the UMC100 provides voltage and power based supervision. Available process data: line to line voltage, power, energy, cosphi, THD (total harmonic distortion)

The intelligent motor controller UMC100.3 DC uses a 110...240 V AC/DC supply and is suitable to protect against overload. It can be connected to a variety of communication networks and has a wide range of additional parameters to maximize motor protection. This version is also ATEX approved.